Mazda 3 manuals

Tesla Model 3 2017-2022 Owner's Manual: Overview

The touchscreen displays the status of Model 3 at all times. What you see depends on whether the vehicle is:

When Model 3 is parked, the status area shows the gear, estimated range, and an overhead view of the car with buttons you can touch to open the trunks and charge port door. When you press the brake, Model 3 powers up and indicator lights flash briefly along the top. Unless an indicator light applies to the current situation (for example, a seat belt is not fastened), it should turn off. If an indicator light fails to turn on or off, contact Tesla.

Note: The following image is provided for demonstration purposes only. Depending on vehicle options, software version, and market region, the information displayed may be slightly different.


Indicator Lights

The following indicator lights illuminate to advise you or alert you of a specific status or condition.

A brake system fault is detected
or the brake fluid level is low.

The parking brake is manually

A parking brake fault is

Tire pressure warning. The
pressure of a tire is out of range. If a fault with the Tire Pressure Monitoring System (TPMS) is detected, the indicator flashes. View tire pressures in the "Cards" area, located below the touchscreen's car status area, as described in Touchscreen Overview on page 4. For a TPMS fault, contact Tesla.

A seat belt for an occupied seat
is not fastened.

Airbag safety. If this indicator
does not flash on briefly when Model 3 prepares to drive, or if it remains on, contact Tesla immediately.

An ABS (Anti-lock Braking System)
fault is detected.

Front fog lights, if equipped.

Parking lights (side marker
lights, tail lights, and license plate lights) are on.

Low beam headlights are on.

High beam headlights are on and
Auto High Beam is disabled or currently unavailable.

Auto High Beam is enabled and
high beams are on. Model 3 is ready to turn off the high beams if light is detected.

Auto High Beam is enabled but
high beams are not on because light is detected in front of Model 3. When light is no longer detected, high beams automatically turn back on.

This indicator flashes amber when
the electronic stability control systems are actively minimizing wheel spin by controlling brake pressure and motor power.

Electronic stability control
systems are no longer minimizing wheel spin.

Vehicle Hold is actively applying
the brakes.

A door or trunk is open.

The Pedestrian Warning System (if
equipped) has been paused.

Appears when some of the stored
energy in the Battery may not be available due to cold weather conditions. If Model 3 is plugged in, you can heat your Battery by turning on climate control with the mobile app. The snowflake icon disappears when the Battery is sufficiently warm.

Vehicle power is currently being
limited because the energy remaining in the Battery is low or the vehicle's systems are being heated or cooled (indicator light is amber).

Flashes green when the left turn
signal is operating. Both turn signal indicators flash green when the hazard warning flashers are operating.

Flashes green when the right turn
signal is operating. Both turn signal indicators flash green when the hazard warning flashers are operating.

Car Status

Driving Status
When Model 3 is driving (or ready to drive), the touchscreen shows your current driving status and a real-time visualization of the road as detected by the Autopilot components. The visualization ...

Other materials:

Washer Tank Removal/Installation
Vehicles with the washer fluid-level sensor 1. Disconnect the negative battery cable.. 2. Remove the front bumper.. 3. Remove in the order indicated in the table. 1 Washer motor connector 2 Windshield washer hose 3 ...

Hood Disassembly/Assembly
Except Mazdaspeed3 1. Disassemble in the order indicated in the table. 1 Weather strip parting seal 2 Weather strip shroud seal 3 Fasteners A 4 Fasteners B 5 ...

Maintenance Monitor (Type B audio)
Select the icon on the home screen to display the “Applications” screen. Select “Maintenance” to display the maintenance list screen. Switch the tab and select the setting item you want to change. You can customize settings in the setup display as follows: ...

© 2016-2022 Copyright