Mazda 3 manuals

Tesla Model 3 2017-2022 Owner's Manual: Overview

The touchscreen displays a map at all times.

To move the map in any direction, hold and drag a finger. To rotate the map in any direction, hold and turn two fingers.

To set the map's orientation, touch the icon in the top right corner of the map:

North Up - North is always at the
top of the screen.

Heading Up - The direction you
are driving is always at the top of the screen. The map rotates as you change direction. This icon has an integrated compass that indicates the direction you are driving.

Note: When navigating, this icon also allows you to view the route overview view and guide you by displaying the current portion of your navigation route

When you rotate or move the map, your current location is no longer tracked. The message "Tracking Disabled" displays briefly next to the map orientation icon and the icon turns gray. To re-enable tracking, touch the map's orientation icon to choose North Up or Heading Up.

Touch the + and - icons to zoom the map in and out on your current or chosen location.

When you zoom in or out using these icons, tracking remains enabled.

Touch the following icons to customize what the map displays and to access navigation settings:

Note: These icons disappear after a few seconds when not in use. Touch anywhere on the map to re-display them.

Display/hide satellite imagery (if
equipped with premium connectivity).

Display/hide traffic conditions (if
equipped with premium connectivity). Green lines indicate no traffic; orange lines indicate light traffic; red lines indicate moderate traffic; and pink lines indicate heavy traffic. To ensure traffic is easy to identify along a navigation route, green traffic lines display under the blue route line, whereas orange, red, and pink traffic lines display on top of the blue route line.

Display/hide all charging
locations and a popup list that includes the city and proximity of the corresponding stations on the map.

Charging locations include Tesla Superchargers, destination chargers, and public chargers that you have used previously

Note: Superchargers are always displayed on the map, even when charging locations are not displayed.

Increase or decrease the volume
of spoken navigation instructions by touching - or +, respectively.

Decreasing all the way to the left mutes the instructions. You can also mute navigation instructions when a navigation route is active by touching the volume icon on the turn-by-turn direction list.

Customize how the navigation system works by adjusting these settings (the available settings vary depending on your market region and vehicle configuration):

Note: You can also access the above navigation settings by touching Controls > Navigation.

Note: The volume setting applies only to the navigation system's spoken instructions. Volume for Media Player and Phone remains unchanged.

Drop a pin by pressing and holding your finger anywhere on the map. When you drop a pin, or touch an existing pin, the chosen location is centered on the map, and a popup window provides information about the location. From this popup, you can navigate to the location, call the location (if a phone number is available) and add or remove the location from your list of favorite destinations

Maps and Navigation
...

Navigating
To navigate to a location, touch Navigate, send the destination from your phone, or speak a voice command. You can enter or speak an address, landmark, business, etc. You can also choose a saved H ...

Other materials:

Blower Motor Removal [Full Auto Air Conditioner]
NOTE: The blower motor is located on the A/C unit as shown in the figure. Perform the work from the front passenger side in the posture shown in the figure. 1. Set the air intake mode to FRESH. 2. Disconnect the negative battery cable. 3. Remove the following ...

Brake Fluid Pressure Sensor Inspection
1. Switch the ignition to off. 2. Install the SSTs to the master cylinder (secondary side) as shown in the figure. NOTE: When installing the SST (49 D043 0A0) to the master cylinder, use a commercially available flare nut wrench (flare nut across flat 12 mm {0.47 in}). ...

Manifold Absolute Pressure (Map) Sensor/Intake Air Temperature (Iat) Sensor No.2 Removal/Installation [Skyactiv G 2.0]
NOTE: Because the IAT sensor No.2 is integrated in the MAP sensor, replacing the IAT sensor No.2 includes replacement of the MAP sensor/IAT sensor No.2. 1. Remove the battery cover.. 2. Disconnect the negative battery cable.. 3. Disconnect the MAP sensor/IAT sensor No.2 connecto ...

2016-2022 Copyright www.mazda3tech.com