Mazda 3 manuals

Tesla Model 3 2017-2022 Owner's Manual: Using Smart Summon

  1. Open the Tesla mobile app, and press SUMMON.
  2. Press the Smart Summon icon located in the center of the image of your Model 3. It may take several seconds for Smart Summon to start up.

Note: You can use Standby Mode to eliminate the delay that occurs when Smart Summon is starting up

The mobile app displays a map with a blue circle, which represents the maximum proximity of 213 feet (65 meters) that you must maintain between your phone and Model 3. The blue dot on the map represents your location, and the red arrow represents the location of Model 3.

  1. Position yourself anywhere within the blue circle where you have a clear line of sight to Model 3.
  2.  You can now operate Smart Summon using either of these modes:

Note: To subsequently change the location, lift your finger, reposition the map, then press and hold GO TO TARGET again.

To stop Model 3 at any time, simply release the COME TO ME or GO TO TARGET button.

The map's crosshair icon toggles
between GO TO TARGET and COME TO ME modes. When COME TO ME mode is selected, the icon is blue.

Note: The map also has an icon that allows you to display/hide satellite imagery.

Immediately after initiating Smart Summon in either mode, hazard lights briefly flash, mirrors fold, and Model 3 shifts into the appropriate driving gear (Drive or Reverse). Model 3 then slowly moves to within 3 feet (1 meter) of you (COME TO ME) or your chosen destination (GO TO TARGET), navigating obstacles as needed. As Model 3 moves, the corresponding red arrow on the map also moves to show the vehicle's location. As you move, the corresponding blue dot also moves to show your location.

In either mode, Model 3 stops moving and shifts into park when:

Note: If Smart Summon moves Model 3 forward three feet and then backwards two feet, this is considered five feet of travel.

Note: There is no need to look at the mobile app-just hold down the button while keeping your eye on Model 3 and its driving path at all times, remaining ready to release the button to stop the vehicle if needed.

If equipped and Auto HomeLink is enabled for Summon (touch Controls > Autopilot > Summon > Use Auto HomeLink, Smart Summon automatically opens a HomeLink device if you start the Smart Summon maneuver when Model 3 is located inside a garage. The mobile app informs you that the door has opened.

Warning: When you release the button to stop Model 3, a slight delay occurs before the vehicle stops. Therefore, it is critical that you pay close attention to the vehicle's driving path at all times and proactively anticipate obstacles that the vehicle may be unable to detect.

Warning: Use extreme caution when using Smart Summon in environments where movement of obstacles can be unpredictable. For example, where people, children or animals are present.

Warning: Smart Summon may not stop for all objects (especially very low objects such as some curbs, or very high objects such as a shelf) and may not react to all oncoming or side traffic. Pay attention and be ready to stop Model 3 at all times by releasing the button on the mobile app.

Standby Mode

To keep Model 3 ready to Summon and reduce the time it takes to warm up, turn on Standby Mode. Touch Controls > Autopilot > Customize Summon > Standby Mode. When Standby Mode is turned on, you can conserve Battery energy by disabling Standby Mode at these locations:

Note: To conserve energy, Smart Summon automatically exits Standby mode from midnight to 6:00 am. During these hours, you will experience a delay as Smart Summon starts up.

Note: Additional battery power may be consumed while Standby Mode is active.

Note: For details on how to designate a location as Home, Work, or Favorites

Smart Summon
Smart Summon (if equipped) is designed to allow you to move Model 3 to your location (using your phone's GPS as a target destination) or to a location of your choice, maneuvering around and st ...

Stopping or Canceling Smart Summon
Smart Summon stops Model 3 whenever you release the button on the mobile app. To resume the Smart Summon session, simply press the COME TO ME or GO TO TARGET button again. Warning: Always anticip ...

Other materials:

Warning Light
The warning light turns on when the system has a malfunction. Refer to Warning Lights on . Brake Pad Wear Indicator When the disc brake pads become worn, the built-in wear indicators contact the disc plates. This causes a screeching noise to warn that the pads should be replaced. When ...

Side Air Bag Sensor No. 1 Removal/Installation [Two Step Deployment Control System]
WARNING: Handling the side air bag sensor improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the air bag system service warnings and cautions before handling the side air bag sensor.. 1. Switch the ignition to off. 2. Disconnec ...

Operation of Automatic Air Conditioning
Set the mode selector dial to the AUTO position. Set the air intake selector to the outside air position (indicator light turned off). NOTE If the recirculated air position is used for long periods in cold weather or high humidity, the windshield may fog up more easily. Set the f ...

2016-2022 Copyright