Mazda 3 Service Manual: A/C Unit Disassembly/Assembly

Mazda 3 Service Manual / HVAC / A/C / A/C Unit Disassembly/Assembly

1. Disassemble in the order indicated in the table.

CAUTION:

If a non-specified grease is used, it may result in abnormal noise or improper operation of the links. Apply only the specified grease to each link.

2. Assemble in the reverse order of disassembly.

X: Applicable—: Not applicable


Step	Part name	Disassembly/assembly of main parts
Step	Part name	Heater core	Evaporator temperature sensor	Evaporator
1	Adhesive polyurethane (1)	-	-	-
2	Blower case (1)	-	-	-
3	Blower case (2)	-	-	-
4	Air intake door	-	-	-
5	Air intake link set	-	-	-
6	Air intake actuator	-	-	-
7	Blower motor pipe	-	-	-
8	Blower motor	-	-	-
9	Power MOS FET (Full-auto air conditioner)	-	-	-
10	Resistor (Manual air conditioner)	-	-	-
11	Plate	-	X	X
12	Air filter	-	X	X
13	Driver-side air mix actuator (Full-auto air conditioner)	-	-	-
14	Driver-side air mix link set (Full-auto air conditioner)	-	-	-
15	Passenger-side air mix actuator (Full-auto air conditioner)	-	-	-
16	Passenger-side air mix link set (Full-auto air conditioner)	-	-	-
17	Air mix link set (Manual air conditioner)	-	-	-
18	Airflow mode actuator (Full-auto air conditioner)	-	-	-
19	Airflow mode link set	-	-	-
20	Airflow mode link set (Manual air conditioner)	-	-	-
21	Polyurethane foam (1)	X	X	X
22	Plate cover	X	X	X
23	Adhesive polyurethane (2) (See Adhesive Polyurethane (2) Assembly Note.)	X	X	X
24	Evaporator pipe	X	X	X
25	Cover	X	X	X
26	Heater core	-	X	X
27	A/C case (1)	-	X	X
28	Expansion valve	-	X	X
29	Evaporator	-	-	-
30	A/C case (2)	-	-	-
31	Evaporator temperature sensor .	-	-	-
32	Polyurethane foam (2)	-	-	-
33	Bolt	-	-	-
34	A/C case (3)	-	-	X
35	A/C case (4)	-	-	X
36	Door damper	-	-	-

Evaporator Temperature Sensor Assembly Note

1. Assemble the evaporator temperature sensor as shown in the figure.

CAUTION:

When installing the evaporator temperature sensor without replacing the evaporator, assemble the evaporator temperature sensor with the installation position slid to the left of the previous position by 1 line. If the evaporator temperature sensor is assembled to the previously installed position, it may not function due to poor contact of the fin surface with the sensor detection area caused by fin deformation.

NOTE:

Replace the evaporator in which the evaporator temperature sensor cannot be correctly positioned.

Adhesive Polyurethane (2) Assembly Note

1. Assemble the adhesive polyurethane as shown in the figure.

A/C Compressor Removal/Installation

1. Disconnect the negative battery cable.. 2. Discharge the refrigerant.. 3. Remove the aerodynamic under cover No.2.. 4. Remove the drive belt.. 5. Remove the water hose bracket. CAUTIO ...

A/C Unit Removal/Installation

1. Set the air mix mode to MAX COLD. 2. Disconnect the negative battery cable.. 3. Discharge the refrigerant.. 4. Drain the engine coolant.. 5. Remove the plug hole plate. 6. Remove the char ...

Other materials:

Condenser Removal/Installation
1. Disconnect the negative battery cable.. 2. Discharge the refrigerant.. 3. Drain the engine coolant.. 4. Remove the air cleaner.. 5. Remove the aerodynamic under cover No.2.. 6. Remove the aerodynamic under cover No.1.. 7. Remove the front bumper.. 8. Disconnect the radiator hose fro ...

Rear Brake (Disc) Inspection
Brake Judder Repair Hints Description 1. Brake judder concern has the following 3 characteristics: Steering wheel vibration 1. The steering wheel vibrates in the rotation direction. This characteristic is most noticeable when applying brakes at a vehicle speed of 100—140 km/h {62.2—86.9 mph ...

Vehicle Speed Sensor (VSS) Removal/Installation [FS5 A EL]
CAUTION: If foreign materials are stuck to the sensor, disturbance by magnetic flux can cause sensor output to be abnormal and thereby negatively affect control. Make sure that foreign materials such as iron filings are not stuck to the sensor during installation. 1. Perform t ...