Mazda 3 Service Manual: ABS HU/CM Inspection

Mazda 3 Service Manual / Brakes / Brake Control, Vehicle Dynamics / ABS / ABS HU/CM Inspection

1. Disconnect the ABS HU/CM connector..

2. Connect the negative battery cable..

3. Attach the tester lead to the ABS HU/CM wiring harness-side connector and inspect the voltage, continuity, or resistance according to the standard (reference value) in the table below.

Standard (reference)


Terminal	Signal name	Connected to	Measured item	Measured terminal (measurement condition)	Standard	Inspection item(s)
A	−	−	−	−	−	−
B	Ground	Ground point	Continuity	B—ground point	Continuity detected	Wiring harness (B—ground point)
C	RR wheel-speed (-)	RR ABS wheel-speed sensor	Continuity	C–RR ABS wheel-speed sensor connector terminal B	Continuity detected	Wiring harness (C–RR ABS wheel-speed sensor connector terminal B)
D	−	−	−	−	−	−
E	RR wheel-speed (+)	RR ABS wheel-speed sensor	Continuity	E–RR ABS wheel-speed sensor connector terminal A	Continuity detected	Wiring harness (E–RR ABS wheel-speed sensor connector terminal A)
F	−	−	−	−	−	−
G	−	−	−	−	−	−
H	CAN_H	DLC-2 (CAN_H)	This terminal is used for communication and cannot be used for malfunction determination during terminal voltage inspection.Perform a DTC inspection.
I	LF wheel-speed (+)	LF ABS wheel speed sensor	Continuity	I–LF ABS wheel-speed sensor connector terminal A	Continuity detected	Wiring harness (I–LF ABS wheel-speed sensor connector terminal A)
J	−	−	−	−	−	−
K	LF wheel-speed (-)	ABS wheel-speed sensor (LF)	Continuity	K–LF ABS wheel-speed sensor connector terminal B	Continuity detected	Wiring harness (K–LF ABS wheel-speed sensor connector terminal B)
L	CAN_L	DLC-2 (CAN_L)	This terminal is used for communication and cannot be used for malfunction determination during terminal voltage inspection.Perform a DTC inspection.
M	−	−	−	−	−	−
N	Power supply (System)	Ignition switch or IG1 relay	Voltage	Switch the ignition to ON	B+	Wiring harness (N—ignition switch or IG1 relay)
N	Power supply (System)	Ignition switch or IG1 relay	Voltage	Switch the ignition to off	1 V or less	Wiring harness (N—ignition switch or IG1 relay)
O	RF wheel-speed (-)	RF ABS wheel-speed sensor	Continuity	O–RF ABS wheel-speed sensor terminal B	Continuity detected	Wiring harness (O–RF ABS wheel-speed sensor connector terminal B)
P	−	−	−	−	−	−
Q	RF wheel-speed (+)	RF ABS wheel-speed sensor	Continuity	Q–RF ABS wheel-speed sensor terminal A	Continuity detected	Wiring harness (Q–RF ABS wheel-speed sensor connector terminal A)
R	−	−	−	−	−	−
S	−	−	−	−	−	−
T	−	−	−	−	−	−
U	LR wheel-speed (+)	LR ABS wheel-speed sensor	Continuity	U–LR ABS wheel-speed sensor connector terminal A	Continuity detected	Wiring harness (U–LR ABS wheel-speed sensor connector terminal A)
V	−	−	−	−	−	−
W	LR wheel-speed (-)	LR ABS wheel-speed sensor	Continuity	W–LR ABS wheel-speed sensor connector terminal B	Continuity detected	Wiring harness (W–LR ABS wheel-speed sensor connector terminal B)
X	−	−	−	−	−	−
Y	Power supply (Solenoid operation, ABS motor operation)	Battery	Voltage	Under any condition	B+	Wiring harness (Y–battery)
Z	−	−	−	−	−	−

ABS

...

ABS HU/CM Removal/Installation

WARNING: If the ABS HU/CM configuration is not completed, it could result in an unexpected accident due to the ABS being inoperative. If the ABS HU/CM or ABS CM is replaced, always use t ...

Other materials:

Replacing Exterior Light Bulbs
Headlights (With xenon fusion headlights) Low/High beam bulbs You cannot replace the low/high beam bulbs by yourself. The bulbs must be replaced at an Authorized Mazda Dealer. Headlights (With halogen headlights) Low-beam bulbs If you are changing the right bulb, start the engine, turn ...

License Plate Light Removal/Installation
1. Disconnect the negative battery cable.. 2. Remove the lens.. 3. Insert a tape-wrapped fastener remover to the position shown in the figure, release the tabs. 4. Pull the rear bumper in the direction of the arrow (1) in the figure, and pull out the license plate lights in the directi ...

Glass Antenna Inspection
4SD 1. Disconnect the negative battery cable.. 2. Disconnect the antenna amplifier connector B.. 3. Disconnect the antenna feeder No.3 connector C. (with audio unit (with display)). 4. Inspect the glass antenna for damage visually. 5. Inspect for continuity between the glass antenna termin ...