Mazda 3 Service Manual: ABS HU/CM Inspection

Mazda 3 Service Manual / Brakes / Brake Control, Vehicle Dynamics / Sensors, Switches, Relays / ABS HU/CM Inspection

1. Disconnect the ABS HU/CM connector..

2. Connect the negative battery cable..

3. Attach the tester lead to the ABS HU/CM wiring harness-side connector and inspect the voltage, continuity, or resistance according to the standard (reference value) in the table below.

Standard (reference)


Terminal	Signal name	Connected to	Measured item	Measured terminal (measurement condition)	Standard	Inspection item(s)
A	−	−	−	−	−	−
B	Ground	Ground point	Continuity	B—ground point	Continuity detected	Wiring harness (B—ground point)
C	RR wheel-speed (-)	RR ABS wheel-speed sensor	Continuity	C–RR ABS wheel-speed sensor connector terminal B	Continuity detected	Wiring harness (C–RR ABS wheel-speed sensor connector terminal B)
D	−	−	−	−	−	−
E	RR wheel-speed (+)	RR ABS wheel-speed sensor	Continuity	E–RR ABS wheel-speed sensor connector terminal A	Continuity detected	Wiring harness (E–RR ABS wheel-speed sensor connector terminal A)
F	−	−	−	−	−	−
G	−	−	−	−	−	−
H	CAN_H	DLC-2 (CAN_H)	This terminal is used for communication and cannot be used for malfunction determination during terminal voltage inspection.Perform a DTC inspection.
I	LF wheel-speed (+)	LF ABS wheel speed sensor	Continuity	I–LF ABS wheel-speed sensor connector terminal A	Continuity detected	Wiring harness (I–LF ABS wheel-speed sensor connector terminal A)
J	−	−	−	−	−	−
K	LF wheel-speed (-)	ABS wheel-speed sensor (LF)	Continuity	K–LF ABS wheel-speed sensor connector terminal B	Continuity detected	Wiring harness (K–LF ABS wheel-speed sensor connector terminal B)
L	CAN_L	DLC-2 (CAN_L)	This terminal is used for communication and cannot be used for malfunction determination during terminal voltage inspection.Perform a DTC inspection.
M	−	−	−	−	−	−
N	Power supply (System)	Ignition switch or IG1 relay	Voltage	Switch the ignition to ON	B+	Wiring harness (N—ignition switch or IG1 relay)
N	Power supply (System)	Ignition switch or IG1 relay	Voltage	Switch the ignition to off	1 V or less	Wiring harness (N—ignition switch or IG1 relay)
O	RF wheel-speed (-)	RF ABS wheel-speed sensor	Continuity	O–RF ABS wheel-speed sensor terminal B	Continuity detected	Wiring harness (O–RF ABS wheel-speed sensor connector terminal B)
P	−	−	−	−	−	−
Q	RF wheel-speed (+)	RF ABS wheel-speed sensor	Continuity	Q–RF ABS wheel-speed sensor terminal A	Continuity detected	Wiring harness (Q–RF ABS wheel-speed sensor connector terminal A)
R	−	−	−	−	−	−
S	−	−	−	−	−	−
T	−	−	−	−	−	−
U	LR wheel-speed (+)	LR ABS wheel-speed sensor	Continuity	U–LR ABS wheel-speed sensor connector terminal A	Continuity detected	Wiring harness (U–LR ABS wheel-speed sensor connector terminal A)
V	−	−	−	−	−	−
W	LR wheel-speed (-)	LR ABS wheel-speed sensor	Continuity	W–LR ABS wheel-speed sensor connector terminal B	Continuity detected	Wiring harness (W–LR ABS wheel-speed sensor connector terminal B)
X	−	−	−	−	−	−
Y	Power supply (Solenoid operation, ABS motor operation)	Battery	Voltage	Under any condition	B+	Wiring harness (Y–battery)
Z	−	−	−	−	−	−

Sensors, Switches, Relays

...

ABS HU/CM Removal/Installation

WARNING: If the ABS HU/CM configuration is not completed, it could result in an unexpected accident due to the ABS being inoperative. If the ABS HU/CM or ABS CM is replaced, always use t ...

Other materials:

Front Fog Light Bulb Removal/Installation
Except Mazdaspeed3 1. Disconnect the negative battery cable.. 2. Slightly bend back the mudguard.. 3. Disconnect the connector. 4. Rotate the front fog light bulb in the direction of the arrow shown in the figure. 5. Remove the front fog light bulb. CAUTION: A haloge ...

Flashing the Headlights
To flash the headlights, pull the lever fully towards you (the headlight switch does not need to be on). The headlight high-beam indicator light in the instrument cluster illuminates simultaneously. The lever will return to the normal position when released. ...

Battery Removal/Installation [Mzr 2.0, Mzr 2.5]
1. Remove in the order indicated in the table. 2. Install in the reverse order of removal. 1 Battery cover (See Battery Cover Removal Note.) (See Battery Cover Installation Note.) 2 Negative battery cable 3 ...