Mazda 3 Service Manual: Battery Recharging [Mzr 2.3 Disi Turbo]
Using GR8-1291:
(See GR8-1291 INSTANT TRAINING MODULE (VIDEO) .)
WARNING:
-
Keep all flames away from the battery, otherwise evaporated gas from the battery fluid may catch fire and cause serious injury.
1. Remove the battery filler caps and check the water level. If necessary, add water to the appropriate level. Reinstall the caps.
2. Attach the large red clamp to the positive battery terminal and the large black clamp to the negative terminal.
3. Select the diagnostic icon in the Main Menu, then press the NEXT key.
4. Follow the on-screen instructions to input the appropriate information. Refer to the Mazda GR8-1291 Instruction Manual for more information.
5. The GR8-1291 will test and charge the battery. Before the diagnostic charging results are displayed, use the keypad on the Control Module to input the last 5 digits of the vehicle's VIN and press NEXT to continue.
6. After the charging is completed, the Mazda GR8-1291 will print out the diagnostic charging results and display one of the following results listed below. Review the results and follow the action step for the displayed result.
|
Battery Tester Display |
Action Step |
|
GOOD BATTERY |
Return the battery to service. |
|
REPLACE BATTERY |
Replace the battery. |
|
BAD CELL - REPLACE |
Replace the battery. WARNING:
|
|
SIDE POST TEST |
Test data was inconclusive using the side post. Retest using side post adapters. |
|
JUMP START POST |
Data was inconclusive using the jump start post. Retest at the battery terminals. |
Without Using GR8-1291:
WARNING:
-
Keep all flames away from the battery, otherwise evaporated gas from the battery fluid may catch fire and cause serious injury.
-
Remove the battery filler caps when recharging to prevent battery deformation or damage.
CAUTION:
-
Do not quick charge for more than 30 min. Otherwise, it will damage the battery.
1. Remove the battery and then place it in a pan of water.
2. Remove the battery filler caps.
3. Connect a battery charger to the battery and adjust the charging current as follows.
-
Battery slow charge current
-
55D23L (48): 4.5—5.5 A
-
75D23L (52): 5.0—6.0 A
-
Battery quick charge current [30 min]
-
55D23L (48): 30 A
-
75D23L (52): 35 A
4. After the battery is recharged, verify that the voltage is within the specification and remains at the same value for 1 h or more
after the recharging has been completed.
-
If not within specification, replace the battery.
-
Standard voltage
-
12.4 V or more
Battery Recharging [Mzr 2.0, Mzr 2.5]
Using GR8-1291:
(See GR8-1291 INSTANT TRAINING MODULE (VIDEO) .)
WARNING:
Keep all flames away from the battery, otherwise evaporated gas from the
battery fluid may catch fire and cause s ...
Battery Recharging [Skyactiv G 2.0]
Using GR8-1291:
(See GR8-1291 INSTANT TRAINING MODULE (VIDEO) .)
WARNING:
Keep all flames away from the battery, otherwise evaporated gas from the
battery fluid may catch fire and cause s ...
Other materials:
Schedule 1
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if
necessary.
R: Replace
L : Lubricate
T: Tighten
Remarks:
*1 Use of FL-22 is recommended when replacing engine coolant. Using engine
coolant other than FL-22 may
cause serious damage to the engine and c ...
Fire Extinguisher Installation [Arab Gulf Cooperation Council]
WARNING:
Handling a front seat (with built-in side air bag) improperly can accidentally
operate (deploy) the air bag, which may seriously injure you. Read the service
warnings before handling a front seat (with built-in side air bag)..
CAUTION:
After removing a front seat ...
Rear Seat Back Removal/Installation
1. Remove the rear seat cushion..
2. Remove the rear buckle installation bolt..
3. Fold the rear seat back.
4. Remove the bolts.
5. Remove the rear seat back from the rear seat back bracket by pulling the rear
seat back in the direction of the arrow shown in the figure.
6. Remove ...
