Mazda 3 Owners Manual: Battery Runs Out

Mazda 3 Owners Manual / If Trouble Arises / Battery Runs Out

Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If you feel unsure about jump-starting, we strongly recommend that you have a competent service technician do the work.

WARNING

Follow These Precautions Carefully: To ensure safe and correct handling of the battery, read the following precautions carefully before using the battery or inspecting it.

Do not allow the
positive terminal to contact any other metal object that could cause sparks: Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced during normal battery operation, could ignite and cause the battery to explode. An exploding battery can cause serious burns and injuries. When working near a battery, do not allow metal tools to contact the positive or negative terminal of the battery.

Keep all fl ames,
including cigarettes, and sparks away from open battery cells: Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced during normal battery operation, could ignite and cause the battery to explode. An exploding battery can cause serious burns and injuries.

Do not jump-start a frozen battery or one with a low fl uid level: Jump-starting a frozen battery or one with a low fl uid level is dangerous. It may rupture or explode, causing serious injury.

Connect the negative cable to a good ground point away from the battery: Connecting the end of the second jumper cable to the negative terminal of the discharged battery is dangerous.

A spark could cause the gas around the battery to explode and injure someone.

Route the jumper cables away from parts that will be moving: Connecting a jumper cable near or to moving parts (cooling fans, belts) is dangerous. The cable could get caught when the engine starts and cause serious injury.

CAUTION Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in series or a 24 V motor generator set).

Mazda 3. Battery Runs Out

Remove the battery cover.

Mazda 3. Battery Runs Out

Make sure the booster battery is 12 V and that its negative terminal is grounded.
If the booster battery is in another vehicle, do not allow both vehicles to touch. Turn off the engine of the vehicle with the booster battery and all unnecessary electrical loads in both vehicles.
Connect the jumper cables in the exact sequence as in the illustration.

Connect one end of a cable to the positive terminal on the discharged battery (1).
Attach the other end to the positive terminal on the booster battery (2).
Connect one end of the other cable to the negative terminal of the booster battery (3).
Connect the other end to the ground point indicated in the illustration away from the discharged battery (4).

Start the engine of the booster vehicle and run it a few minutes. Then start the engine of the other vehicle.
(With i-ELOOP system) The i-ELOOP indicator light may flash after the engine is started. The indicator light turns off when the engine is running and the charging is completed.
Make sure the i-ELOOP indicator light is turns off before driving.

Mazda 3. Battery Runs Out

NOTE

If the vehicle is driven with the i-ELOOP indicator light flashing, a beep sound is heard.
If the steering wheel is operated with the i-ELOOP indicator light flashing, it may feel heavier than normal, however, this does not indicate a malfunction.
The steering operation will return to normal when the i-ELOOP indicator light turns off.
Do not remove the jumper cables while the i-ELOOP indicator light is flashing.

When finished, carefully disconnect the cables in the reverse order described in the illustration.
If the battery cover has been removed, install it in the reverse order of removal.

NOTE Verify that the covers are securely installed.

Mounting the Spare Tire

Remove dirt and grime from the mounting surfaces of the wheel and hub, including the hub bolts, with a cloth. WARNING Make sure the mounting surfaces of the wheel, hub and ...

Emergency Starting

...

Other materials:

Front Door Trim Removal/Installation
1. Disconnect the negative battery cable.. 2. Remove the inner garnish.. 3. Move the hook in the direction of arrow shown in the figure using a tape-lapped flathead screwdriver and detach it from the front door trim. CAUTION: Affix protective tape to the front door trim and assis ...

Active Driving Display
WARNING Always adjust the display brightness and position with the vehicle stopped: Adjusting the display brightness and position while driving the vehicle is dangerous as doing so could distract your attention from the road ahead and lead to an accident. ...

Steering Wheel And Column Removal/Installation [Without Advanced Keyless Entry And Push Button Start System]
WARNING: Handling the air bag module improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the service warnings before handling the air bag module.. 1. Remove the driver-side front scuff plate.. 2. Remove the driver-side front sid ...