NOTE:
For the clutch pedal inspection, note the followings and measure each inspection location.
Measure the center of the upper surface of the pedal pad for each inspection.
If the distance from the pedal pad to the floor covering is measured, measure the shortest distance from the center of the upper surface of the pedal pad to the floor covering.
Pedal Inspection Preparation
1. Verify that there is no malfunction in the clutch fluid level..
2. Verify that there is no clutch fluid leakage..
Pedal Height Inspection
1. Perform “Pedal Inspection Preparation”..
2. Measure the pedal height with the clutch pedal released as shown in the figure.
142.8 mm {5.622 in}
If it is not the specification, replace the clutch pedal..
Pedal Free Play Inspection
1. Perform “Pedal Inspection Preparation”..
2. Depress the clutch pedal by hand until clutch resistance is felt, and measure the pedal free play as shown in the figure.
15 mm {0.59 in} or less
If it exceeds the specification, replace the clutch pedal..
Pedal Full Stroke Inspection
1. Perform “Pedal Inspection Preparation”..
2. Depress the clutch pedal from the released condition to the full depression position, and measure the pedal full stroke as shown in the figure.
140 mm {5.51 in}
If it is not the specification, replace the clutch pedal..
Clutch Disengagement Point Inspection
WARNING:
When performing the following procedure, make sure that the area around the vehicle is free of people or objects as the vehicle might move suddenly.
NOTE:
There are two methods for the clutch disengagement point inspection as follows: Perform any of the following inspection procedures for the clutch disengagement point inspection.
Procedure A: Procedure for measuring the distance from the clutch disengagement point to the floor.
Procedure B: Procedure for measuring the distance from the clutch disengagement point to the maximum clutch pedal depression position.
Procedure A
1. Perform “Pedal Inspection Preparation”..
2. Verify that the pedal height is normal..
3. Verify that the pedal free play is normal..
4. Verify that the pedal full stroke is normal..
5. Apply the parking brake and fix the front and rear of the wheels with the wheel chocks.
6. Start the engine.
7. With the clutch pedal depressed, move the shift lever to the position just before engaging the reverse gear. (Do not shift completely to reverse position)
8. Gradually release the clutch pedal and then hold it at the point where the sound of gear-grinding begins (clutch disengagement point).
9. Measure distance A as shown in the figure when the clutch pedal is at the clutch disengagement point.
52.3 mm {2.06 in} or more
If it is less than the specification, bleed the air from the clutch system..
Procedure B
1. Perform “Pedal Inspection Preparation”..
2. Verify that the pedal height is normal..
3. Verify that the pedal free play is normal..
4. Verify that the pedal full stroke is normal..
5. Apply the parking brake and fix the front and rear of the wheels with the wheel chocks.
6. Start the engine.
7. With the clutch pedal depressed, move the shift lever to the position just before engaging the reverse gear. (Do not shift completely to reverse position)
8. Gradually release the clutch pedal and then hold it at the point where the sound of gear-grinding begins (clutch disengagement point).
9. Depress the clutch pedal from the clutch disengagement point to the full depression position, and measure distance B as shown in the figure.
12.5 mm {0.492 in} or more
If it is less than the specification, bleed the air from the clutch system..
Seat Weight Sensor Inspection [Two Step Deployment Control System]
CAUTION:
If any of the following work is performed, perform the seat weight sensor
inspection using the M-MDS.
Removal of the passenger-side seat
Loosening and retightening of passenger’s seat fixing bolts
Or, the vehicle is involved in a collision
...
Transaxle Oil Replacement [A26 M R]
1. Park the vehicle on level ground.
2. Remove the aerodynamic under cover No.2..
3. Remove the drain plug and gasket.
4. Drain the oil into a suitable container.
5. Install a new gasket and the drain plug.
Tightening torque
28—51 N·m {2.9—5.2 kgf·m, 21—37 ft·lbf}
6. Remo ...
Transmitter
NOTE
(With theft-deterrent system)
The hazard warning lights flash when
the theft-deterrent system is armed or
turned off.
Refer to Theft-Deterrent System on .
(With the advanced keyless function)
A beep sound can be heard for
confirmation when the doors and the
l ...