Mazda 3 manuals

Mazda 3 Service Manual: Electric Variable Valve Timing Motor/Driver Removal/Installation [Skyactiv G 2.0]

Mazda 3 Service Manual / Engine / General / Electric Variable Valve Timing Motor/Driver Removal/Installation [Skyactiv G 2.0]

WARNING:

CAUTION:

1. Remove the battery cover..

2. Disconnect the negative battery cable..

3. Remove the plug hole plate..

4. Remove the coolant reserve tank with the hose still connected and set it out of the way..

5. Remove in the order indicated in the table.

6. Install in the reverse order of removal.



1

No. 3 engine mount

(See No.3 Engine Mount Removal Note.)

(See No.3 Engine Mount Installation Note.)

2

Electric variable valve timing motor/driver connector

3

Electric variable valve timing motor/driver

(See Electric Variable Valve Timing Motor/Driver Installation Note.)

4

O-ring


No.3 Engine Mount Removal Note

1. Remove the cooler hose bracket bolt and set the cooler hose aside.


2. Remove the aerodynamic under cover No.2..

CAUTION:

3. Before removing the No.3 engine mount, support the engine (oil pan) using a commercially available engine lifter or garage jack.


4. Remove the No. 3 engine mount.

Electric Variable Valve Timing Motor/Driver Installation Note

1. Install a new O-ring to the O-ring installation groove of the engine front cover.

CAUTION:


2. Install the electric variable valve timing motor/driver using the following procedures.

NOTE:

a. Before installation, rotate the joint of the end of the electric variable valve timing motor so that it is aligned to the joint groove on the electric variable valve timing actuator side.


b. Engage the joint on the end of the electric variable valve timing motor with the joint groove on the electric variable valve timing actuator side.

c. Attach the seal surface.

d. Tighten the electric variable valve timing motor/driver installation bolts.

No.3 Engine Mount Installation Note

NOTE:

1. Tighten the No.3 engine mount stud bolts.


2. Install the No.3 engine mount and temporarily tighten the bolts and nuts.

3. Tighten the No.3 engine mount installation bolts and nuts in the order as shown in the figure.



No.

Tightening torque

1

75—104 N·m {7.7—10 kgf·m, 56—76 ft·lbf}

2

71—93 N·m {7.3—9.4 kgf·m, 53—68 ft·lbf}


4. Remove the engine lifter or garage jack.

5. Install the aerodynamic under cover No.2..

6. Install the cooler hose bracket bolt.

Electric Variable Valve Timing Motor/Driver Inspection [Skyactiv G 2.0]
WARNING: A hot engine can cause severe burns. Turn off the engine and wait until it is cool before servicing. CAUTION: Do not disassemble the electric variable valve timing mo ...

Engine Disassembly/Assembly [Mzr 2.0, Mzr 2.5]
1. Remove the engine from the transaxle.. 2. Remove the generator.. 3. Remove the exhaust system.. 4. Remove the EGR valve.. 5. Remove the intake-air system.. 6. Remove the fuel injectors.. ...

Other materials:

Seat Belt Warning Beep
If the driver's seat belt is not fastened when the ignition is switched ON, a beep sound will be heard for about 6 seconds. If the driver or the front passenger's seat belt is not fastened and the vehicle is driven at a speed faster than about 20 km/h (12 mph), a beep sound will be heard again ...

Adjuster Anchor Removal/Installation
WARNING: The side air bag sensor is attached to the lower part of the B-pillar. When working around the B-pillar, disconnect the negative battery cable or work carefully, avoiding excessive impact to the lower part of the B-pillar. 1. Remove the following parts: a. Front sc ...

Afs (Adaptive Front Lighting System) Control Module Removal/Installation
NOTE: Perform the auto leveling system initialization after newly replacing the AFS control module to assure that the auto leveling system operates correctly. 1. Disconnect the negative battery cable.. 2. Remove the following parts: a. Passenger-side front scuff plate. b. Pass ...

© 2016-2024 Copyright www.mazda3tech.com