Mazda 3 Service Manual: Front Drain Hose Installation
CAUTION:
-
If the front drain hose is pinched or bent anywhere, the water in the hose may not discharge and enter the inside of the vehicle. During and after installation of the trims and the headliner, always make sure there is no interference with the front drain hose. Fix any problem if found.
1. Apply soapy water to the front drain hose inserting area.
2. Insert one end (the wider end) of the front drain hose into the sunroof frame.
3. Install the front drain hose to the clips, parallel to the pillar and free of slack.
4. Insert the front drain hose joint into the hinge pillar inner hole.
5. Connect the auto-dimming mirror connector. (vehicles with auto-dimming mirror)
6. Install the following parts:
a. Headliner.
b. Assist handle.
c. Sunvisor.
d. Map light.
e. C-pillar trim.
f. Trunk side upper trim (5HB).
g. Tire house trim.
h. Rear seat cushion.
i. B-pillar upper trim.
j. Upper anchor of the front seat belt.
k. B-pillar lower trim.
l. Rear scuff plate.
m. A-pillar trim.
n. Sunroof seaming welt
o. Dashboard.
p. Windshield wiper motor.
q. Cowl grille.
r. Front fender molding.
s. Windshield wiper arm and blade.
t. A-pillar trim.
u. multi information display (with multi information display).
v. Information display (with information display).
w. Hole cover.
x. Dashboard upper panel.
y. Center cover.
z. Instrument cluster.
aa. Climate control unit.
ab. Audio unit.
ac. Center panel.
ad. Steering shaft.
ae. Joint cover.
af. Combination switch.
ag. Column cover.
ah. Steering wheel.
ai. Driver-side air bag module.
aj. Knee bolster.
ak. Lower panel.
al. Hood release lever from the lower panel.
am. Selector lever component (ATX).
an. Shift lever component (MTX).
ao. Console.
ap. Side wall.
aq. Shift panel.
ar. Selector lever knob (ATX).
as. Shift lever knob (MTX).
at. Upper panel.
au. Glove compartment.
av. Dashboard under cover.
aw. Front side trim.
ax. Front scuff plate.
ay. Front doors.
7. Connect the rain sensor connector. (Vehicles with auto light / wiper system)
8. Install the rain sensor cover. (Vehicles with auto light / wiper system).
9. Install the seaming welt.
10. Connect the negative battery cable..
Deflector Removal/Installation
1. Fully open the glass panel.
2. Press the spring in the direction shown by the arrow and remove it from the
hook.
3. Remove the deflector.
4. Install in the reverse order of removal. ...
Front Drain Hose Removal
1. Set the air intake mode to FRESH.
2. Set the air mix mode to MAX COLD.
3. Disconnect the negative battery cable.
4. Remove the rain sensor cover. (Vehicles with auto light / wiper system).
...
Other materials:
Input/Turbine Speed Sensor Removal/Installation [FS5 A EL]
CAUTION:
Always use a new bolt. If the removed input/turbine speed sensor installation
bolt is reused, it may cause oil leakage.
A sealant coating is applied to the input/turbine speed sensor installation
bolt to prevent oil leakage from the installation bolt hole which passes ...
Engine Tune Up [Mzr 2.3 Disi Turbo]
NOTE:
If the accelerator pedal is depressed continuously for a specified time,
the engine speed may decrease to the idle speed. This is due to the fuel cut
control operation, which prevents overheating, and it does not indicate a malfunction.
Engine Tune-up Preparation
1. Verify ...
Rear Washer Hose Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the front mudguard (RH)..
3. Disconnect rear washer hose A from the washer motor.
4. Remove the rear washer hose A from clip A, B, C, D, E, F, G.
5. Disconnect joint pipes and remove rear washer hose A.
6. Partially peel back the sea ...
