CAUTION:
If the front fog light aiming is adjusted with cargo in the vehicle, it may not adjust correctly. Adjust the front fog light aiming with the vehicle under the following conditions:
No occupants inside vehicle
Cargo other than spare tire, jack, and tools not loaded
Tire pressure is at specification.
Park the vehicle on level ground
Except Mazdaspeed3
1. Make a screen as shown in the figure using double-weight, white paper.
2. Seat one person in the driver’s seat.
3. Line up the vehicle with the wall so that the center of the front fog light is 3 m {9.8 ft}
away from the wall.
4. Measure the height at the center of the front fog light.
NOTE:
Since the height of the vehicle varies depending on the vehicle situation, measure the height of the center of the front fog light using the actual vehicle.
5. Align the center of the front fog light with the center of the screen.
6. Block the light of the other front fog light using a partition.
7. Start the engine.
NOTE:
If servicing is performed when the engine is stopped and the front fog light illuminates, it could result in a discharged battery. For the aiming adjustment, start the engine and perform servicing while the engine is idling.
8. Turn the front fog lights on.
9. Verify that the brightness border line of the front fog light is at the position indicated on the adjustment screen.
If the brightness border line is not at the position indicated on the adjustment screen, perform the following adjustment.
Loosen the bolt.
Loosen the screw.
Move the front fog light in the direction of the arrow shown in the figure to adjust the brightness border line to the position indicated on the adjustment screen.
Tighten the screw and bolt.
Mazdaspeed3
1. Make a screen as shown in the figure using double-weight, white paper.
2. Seat one person in the driver’s seat.
3. Line up the vehicle with the wall so that the center of the front fog light is 3 m {9.8 ft}
away from the wall.
4. Measure the height at the center of the front fog light.
NOTE:
Since the height of the vehicle varies depending on the vehicle situation, measure the height of the center of the front fog light using the actual vehicle.
5. Align the center of the front fog light with the center of the screen.
6. Block the light of the other front fog light using a partition.
7. Start the engine.
NOTE:
If servicing is performed when the engine is stopped and the front fog light illuminates, it could result in a discharged battery. For the aiming adjustment, start the engine and perform servicing while the engine is idling.
8. Turn the front fog lights on.
9. Verify that the brightness border line of the front fog light is at the position indicated on the adjustment screen.
If the brightness border line is not at the position indicated on the adjustment screen, perform the following adjustment.
Loosen the bolt.
Loosen the screw.
Move the front fog light in the direction of the arrow shown in the figure to adjust the brightness border line to the position indicated on the adjustment screen.
Tighten the screw and bolt.
Electric Power Steering Oil Pump Component Disassembly/Assembly
CAUTION:
The internal parts of the EHPAS control module and motor could be damaged
if they receive an impact. Be careful when handling the EHPAS control module
and motor to prevent the component from getting hit. Replace the electric power
steering oil pump component if it has recei ...
Drive Belt Removal/Installation [Mzr 2.0, Mzr 2.5]
MZR 2.0
A/C drive belt removal
1. Remove the aerodynamic under cover No.2 and splash shield as a single unit..
2. Remove the nut shown in the figure and set the power steering pipe component
out of the way.
3. Set the SST as shown in the figure.
NOTE:
Hold the SST by hand unti ...
Roof Carrier Bracket Removal/Installation
4SD
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Sunroof seaming welt (vehicles with sunroof)
b. Front scuff plate.
c. Rear scuff plate.
d. A-pillar trim.
e. B-pillar lower trim.
f. Upper anchor of the front seat belt installation bolt.
g. B-pillar up ...