Mazda 3 Service Manual: General
- Air Bleeding
- Air Bypass Valve Inspection [Mzr 2.3 Disi Turbo]
- Check Valve Inspection [Skyactiv G 2.0]
- Compression Inspection [Mzr 2.0, Mzr 2.5]
- Compression Inspection [Mzr 2.3 Disi Turbo]
- Compression Inspection [Skyactiv G 2.0]
- Electric Variable Valve Timing Actuator Inspection [Skyactiv G 2.0]
- Electric Variable Valve Timing Actuator, Hydraulic Variable Valve Timing Actuator Removal/Installation [Skyactiv G 2.0]
- Electric Variable Valve Timing Motor/Driver Inspection [Skyactiv G 2.0]
- Electric Variable Valve Timing Motor/Driver Removal/Installation [Skyactiv G 2.0]
- Engine Disassembly/Assembly [Mzr 2.0, Mzr 2.5]
- Engine Disassembly/Assembly [Mzr 2.3 Disi Turbo]
- Engine Disassembly/Assembly [Skyactiv G 2.0]
- Engine Removal/Installation [Mzr 2.0, Mzr 2.5]
- Engine Removal/Installation [Mzr 2.3 Disi Turbo]
- Engine Removal/Installation [Skyactiv G 2.0]
- Engine SST [Mzr 2.0, Mzr 2.5]
- Engine SST [Mzr 2.3 Disi Turbo]
- Engine SST [Skyactiv G 2.0]
- Engine Tune Up [Mzr 2.0, Mzr 2.5]
- Engine Tune Up [Mzr 2.3 Disi Turbo]
- Engine Tune Up [Skyactiv G 2.0]
- Non Return Valve Inspection [Mzr 2.0, Mzr 2.5]
- Non Return Valve Inspection [Mzr 2.3 Disi Turbo]
- Non Return Valve Inspection [Skyactiv G 2.0]
- Plug Hole Plate Removal/Installation [Mzr 2.0, Mzr 2.5]
- Variable Swirl Shutter Valve Actuator Inspection [Mzr 2.3 Disi Turbo]
- Variable Swirl Solenoid Valve Inspection [Mzr 2.3 Disi Turbo]
- Variable Tumble Shutter Valve Actuator Inspection [Mzr 2.0, Mzr 2.5]
- Variable Tumble Solenoid Valve Inspection [Mzr 2.0, Mzr 2.5]
- Variable Valve Timing Actuator Inspection [Mzr 2.0, Mzr 2.5]
- Variable Valve Timing Actuator Inspection [Mzr 2.3 Disi Turbo]
- Variable Valve Timing Actuator Removal/Installation [Mzr 2.0, Mzr 2.5]
- Variable Valve Timing Actuator Removal/Installation [Mzr 2.3 Disi Turbo]
- Hydraulic Variable Valve Timing Actuator Inspection [Skyactiv G 2.0]
Engine
...
Air Bleeding
CAUTION:
If the strainer is removed, impurities may penetrate the power steering system
and damage it. To prevent this, always bleed air with the strainer installed.
Do not ma ...
Other materials:
PID/Data Monitor Inspection [Standard Deployment Control System]
1. Connect the M-MDS (IDS) to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization
screen of the IDS.
a. Select “DataLogger”.
b. Select “Modules”.
c. Select “RCM”.
3. Select the applicable PID from the PID table.
4. Verify the PID data a ...
Keyless Control Module Inspection
1. Remove the following parts:
a. Passenger-side front scuff plate.
b. Passenger-side front side trim.
c. Grove compartment.
d. Passenger-side lower panel.
2. Measure the voltage according to the terminal voltage table.
If the voltages cannot be verified as indicated in the termina ...
Antenna Feeder No.3 Removal/Installation
4SD (With Audio Unit (With Display))
1. Disconnect the negative battery cable..
2. Remove the rain sensor cover. (Vehicles with auto light/wiper system).
3. Disconnect the rain sensor connector. (Vehicles with auto light/wiper system)
4. Partially peel back the seaming welts.
5. Remove the ...
