Mazda 3 Service Manual: Steering Gear And Linkage Disassembly
CAUTION:
-
To prevent damage to the steering gear, secure it to the vise using a copper plate or clean cloth.
1. Disassemble in the order indicated in the table.
|
1 |
Floor seal |
|
2 |
Oil pipe |
|
3 |
Tie-rod end (See Tie-rod End Disassembly Note.) |
|
4 |
Locknut |
|
5 |
Boot clamp |
|
6 |
Boot band (See Boot Band Disassembly Note.) |
|
7 |
Boot |
|
8 |
Tie rod (See Tie Rod Disassembly Note.) |
|
9 |
Locknut (on adjusting cover) (See Locknut (on Adjusting Cover), Adjusting Cover Disassembly Note.) |
|
10 |
Adjusting cover (See Locknut (on Adjusting Cover), Adjusting Cover Disassembly Note.) |
|
11 |
Yoke spring |
|
12 |
Support yoke |
|
13 |
Housing cover |
|
14 |
Locknut (on pinion shaft) |
|
15 |
Return pipe |
|
16 |
Pinion shaft and valve housing component |
|
17 |
Clip |
|
18 |
Stopper |
|
19 |
Steering rack |
|
20 |
Rack bushing |
|
21 |
Oil seal (See Oil Seal Disassembly Note.) |
|
22 |
Mounting rubber (See Mounting Rubber Disassembly Note.) |
|
23 |
Gear housing |
Tie-rod End Disassembly Note
1. Place alignment marks as shown in the figure for proper installation.
2. Remove the tie-rod end.
Boot Band Disassembly Note
1. Insert a flathead screw driver into the boot band as shown in the figure, then press the caulked area outward to remove the boot band.
Tie Rod Disassembly Note
CAUTION:
-
If the steering rack is secured to a vise without using a cloth, the sliding surface of the steering rack could be damaged. Always use a clean cloth when securing the steering rack to the vise.
-
If the steering rack is secured to a vise in the incorrect position, the steering gear could fall off the vise and be damaged during the operation. Always secure the steering rack to the vise in the proper position.
1. Protect the steering rack tooth surface using a clean cloth and secure it using a vise.
2. Remove the tie rod using the SST
.
Locknut (on Adjusting Cover), Adjusting Cover Disassembly Note
1. Remove the locknut using the SST
.
2. Remove the adjusting cover.
Oil Seal Disassembly Note
1. Install the SST
(49 N032 319A) to the gear housing as shown in the figure.
2. Insert the SSTs
(49 F032 303, 49 B032 323) into the valve housing side.
3. Remove the oil seal using the SSTs
and a press.
Mounting Rubber Disassembly Note
1. Remove the mounting rubber from the gear housing using the SSTs
and a press.
Steering Gear And Linkage Assembly
CAUTION:
To prevent damage to the steering gear, secure it to the vise using a copper
plate or clean cloth.
1. Assemble in the order indicated in the table.
1
...
Steering Gear And Linkage Inspection
Steering Rack Inspection
1. Inspect for cracking, damage, and tooth wear.
If there is any malfunction, replace the steering rack.
2. Measure the steering rack warp.
If it ex ...
Other materials:
Fuel Filter (High Pressure) Removal/Installation [Mzr 2.0, Mzr 2.5]
WARNING:
Fuel is very flammable liquid. If fuel spills or leaks from the pressurized
fuel system, it will cause serious injury or death and facility breakage. Fuel
can also irritate skin and eyes. To prevent this, always complete the “Fuel
Line Safety Procedure”, while referring to ...
Rain Sensor Removal/Installation
1. Disconnect the negative battery cable..
2. Spread open the rain sensor cover in the direction of the arrows and disengage
tabs A to remove it.
3. Disconnect the rain sensor connector.
4. Slide rain sensor tab B in the direction of the arrow shown in the figure
and detach tab B. ...
Power Window Main Switch Inspection
1. Disconnect the negative battery cable.
2. Remove the inner garnish. (driver's side).
3. Remove the front door trim. (driver's side).
4. Remove the main switch panel. (driver's side).
5. Connect the power window main switch connector.
6. Connect the negative battery cable..
...
