Mazda 3 Service Manual: Transaxle Fluid Temperature (Tft) Sensor Inspection [FS5 A EL]
CAUTION:
-
Water or foreign objects entering the connector can cause a poor connection or corrosion. Be sure not to drop water or foreign objects on the connector when disconnecting it.
On-Vehicle Inspection
1. Perform the following procedures.
a. Remove the battery cover..
b. Disconnect the negative battery cable.
c. Remove the air cleaner component..
d. Disconnect the coupler component connector.
2. Measure the resistance between the coupler component terminals E and H.
-
If there is any malfunction, replace the TFT sensor..
|
ATF temperature (°C{°F}) |
Resistance (kilohm) |
|
-20 {-4} |
236—324 |
|
0 {32} |
84.3—110 |
|
20 {68} |
33.5—42.0 |
|
40 {104} |
14.7—17.9 |
|
60 {140} |
7.08—8.17 |
|
80 {176} |
3.61—4.15 |
|
100 {212} |
1.96—2.24 |
|
120 {248} |
1.13—1.28 |
|
130 {266} |
0.87—0.98 |
Off-Vehicle Inspection
1. Place the TFT sensor and a thermometer in ATF as shown, and heat the ATF gradually.
WARNING:
-
A hot ATF and beaker can cause severe burns. Do not touch them.
2. Measure the resistance between the coupler component terminals E and H.
-
If there is any malfunction, replace the TFT sensor..
|
ATF temperature (°C{°F}) |
Resistance (kilohm) |
|
-20 {-4} |
236—324 |
|
0 {32} |
84.3—110 |
|
20 {68} |
33.5—42.0 |
|
40 {104} |
14.7—17.9 |
|
60 {140} |
7.08—8.17 |
|
80 {176} |
3.61—4.15 |
|
100 {212} |
1.96—2.24 |
|
120 {248} |
1.13—1.28 |
|
130 {266} |
0.87—0.98 |
Inspection After Transaxle Installation [G66 M R]
NOTE:
Perform the following inspection only when the transaxle has been overhauled.
1. Perform a road test and inspect the following items:
a. No abnormal noise in each shift position. ...
Transaxle Fluid Temperature (Tft) Sensor Removal/Installation [FS5 A EL]
WARNING:
A hot transaxle and ATF can cause severe burns. Turn off the engine and wait
until they are cool.
1. Remove the primary control valve body.
a. Remove the battery cover..
...
Other materials:
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning flasher and
all the t ...
Key Interlock System Inspection
Key Interlock System Inspection
1. Switch the ignition to ON.
2. Perform the following procedures to inspect the key interlock system.
If there is any malfunction, inspect the key interlock solenoid and NOT P
position switch..
a. Verify that the ignition cannot be switched to off ...
Outside Temperature Display
When the ignition is switched ON, the
outside temperature is displayed.
NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and vehicle
conditions:
Significantly cold or hot
temperatures.
...
