Mazda 3 Service Manual: Transmission/Transaxle SST
1: Mazda SST number
2: Global SST number
Example
|
1:49 UN30 3009 2:303-009 Crankshaft damper remover |
|
Clutch [G35M-R]
|
1:49 E011 1A0 2: – Ring gear brake set |
|
1:49 SE01 310A 2: – Clutch disc center tool |
|
1:49 1285 071 2: – Bearing puller |
|
Clutch [G66M-R]
|
1:49 E011 1A0 2: – Ring gear brake set |
|
1:49 SE01 310A 2: – Clutch disc center tool |
|
1:49 1285 071 2: – Bearing puller |
|
Clutch [A26M-R]
|
1:49 E011 1A0 2: – Ring gear brake set |
|
1:49 SE01 310A 2: – Clutch disc center tool |
|
1:49 1285 071 2: – Bearing puller |
|
|
1:49 E027 002 2: – Attachment |
|
1:49 G030 797 2: – Handle |
|
– |
|
Clutch [C66M-R]
|
1:49 UN30 3050 2: 303-050 Engine lifting brackets |
|
1:49 C017 5A0 2: – Engine support set |
|
1:49 L017 5A0 2: – Support hanger |
|
|
1:49 E011 1A0 2: – Ring gear brake set |
|
1:49 SE01 310A 2: – Clutch disc center tool |
|
1:49 1285 071 2: – Bearing puller |
|
Manual Transaxle [G35M-R]
|
1:49 C017 5A0 2: – Engine support set |
|
1:49 G030 795 2: – Oil seal installer |
|
– |
|
Manual Transaxle [G66M-R]
|
1:49 C017 5A0 2: – Engine support set |
|
1:49 G030 796 2: – Body |
|
1:49 G030 797 2: – Handle (Part of 49 G030 795) |
|
|
1:49 M005 797 2: – Handle |
|
– |
– |
||
Manual Transaxle [A26M-R]
|
1:49 C017 5A0 2: – Engine support set |
|
1:49 W027 001 2: – Body |
|
1:49 F027 003 2: – Handle |
|
|
1:49 U027 003 2: – Oil Seal Installer |
|
– |
– |
||
Manual Transaxle [C66M-R]
|
1:49 UN30 3050 2: 303-050 Engine lifting brackets |
|
1:49 C017 5A0 2: – Engine support set |
|
1:49 L017 5A0 2: – Support hanger |
|
|
1:49 G030 797 2: – Handle (Part of 49 G030 795) |
|
1:49 U027 003 2: – Oil Seal Installer |
|
– |
|
Automatic Transaxle [FS5A-EL]
|
1:49 H019 002 2: – Adapter |
|
1:49 0378 400C 2: – Oil pressure gauge set |
|
1:49 B019 901B 2: – Oil pressure gauge |
|
|
1:49 B019 902A 2: – Oil pressure gauge |
|
1:49 D019 910 2: – Adapter (Part of 49 D019 9A2) |
|
1:49 D019 911 2: – Adapter (Part of 49 D019 9A2) |
|
|
1:49 D019 913 2: – Adapter (Part of 49 D019 9A2) |
|
1:49 D019 909 2: – Hose (Part of 49 D019 9A2) |
|
1:49 D019 908 2: – Gauge (Part of 49 D019 9A2) |
|
|
1:49 D019 907 2: – Oil pressure gauge (Part of 49 D019 9A2) |
|
1:49 C017 5A0 2: – Engine support set |
|
1:49 E011 1A0 2: – Ring gear brake set |
|
|
1:49 G030 796 2: – Body (Part of 49 G030 795) |
|
1:49 G030 797 2: – Handle (Part of 49 G030 795) |
|
– |
|
Automatic Transaxle [FW6A-EL]
|
1:49 D019 910 2: – Adapter (Part of 49 D019 9A2) |
|
1:49 D019 911 2: – Adapter (Part of 49 D019 9A2) |
|
1:49 D019 913 2: – Adapter (Part of 49 D019 9A2) |
|
|
1:49 D019 909 2: – Hose (Part of 49 D019 9A2) |
|
1:49 D019 908 2: – Gauge (Part of 49 D019 9A2) |
|
1:49 D019 907 2: – Oil pressure gauge (Part of 49 D019 9A2) |
|
|
1:49 UN30 3050 2: 303-050 Engine lifting brackets |
|
1:49 C017 5A0 2: – Engine support set |
|
1:49 L017 5A0 2: – Support hanger |
|
|
1:49 E011 1A0 2: – Ring gear brake set |
|
1:49 G030 797 2: – Handle (Part of 49 G030 795) |
|
1:49 U027 003 2: – Oil Seal Installer |
|
|
1:49 G030 796 2: – Body (Part of 49 G030 795) |
|
1:49 F027 003 2: – Handle |
|
1:49 U034 204 2: – Dust boot installer |
|
Torque Converter Clutch (TCC) Non Operation [Fw6 A EL]
TROUBLESHOOTING ITEM
Torque converter clutch (TCC) non-operation
DESCRIPTION
TCC does not operate when vehicle reaches TCC oper ...
Up Switch Inspection [FS5 A EL]
1. Perform the following procedures.
a. Remove the battery cover..
b. Disconnect the negative battery cable.
c. Remove the console..
d. Disconnect the selector lever component connector.
...
Other materials:
Operating Tips for CD Player
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or
optical components (prism and lens) in
the CD player may become clouded with
condensation. At this time, the CD will
eject immediately when placed in the unit.
A clouded CD can be corrected s ...
Settings
NOTE
Depending on the grade and specification, the screen display may differ.
Select the icon on the home
screen and display the Settings screen.
Switch the tab and select the setting item you want to change.
You can customize settings in the setup display as follows:
Tab
...
Power Outer Mirror Inspection
Mirror Glass Adjustment Motor
1. Disconnect the negative battery cable..
2. Remove the inner garnish..
3. Disconnect the power outer mirror connector.
4. Remove the front door trim..
5. Apply battery positive voltage and connect the ground to the power outer mirror
terminals and inspect t ...
