Mazda 3 Service Manual: Engine SST [Mzr 2.0, Mzr 2.5]
1: Mazda SST number
2: Global SST number
Example
|
1:49 UN01 052 2:310–D005 Spring lock coupler tool (green) |
|
|
1: 49 C017 5A0 2: – Engine support set |
|
1:49 B011 105 2:– Adapter |
|
1:49 UN20 5072 2:205–072 Holder |
|
|
1:49 B015 102 2:– Remover (Part of 49 B015 1A0) |
|
1:49 B015 103 2:– Installer (Part of 49 B015 1A0) |
|
1:49 B015 104 2:– Hook (Part of 49 B015 1A0) |
|
|
1:– 2:303–507 Crankshaft TDC timing pin |
|
1:49 UN30 3465 2:303–465 Camshaft alignment timing tool |
|
1:49 D032 316 2: – Protractor |
|
|
1:49 UN30 3328 2:303–328 Rear oil seal replacer |
|
1:49 H010 401 2:– Oil seal installer |
|
1: – 2: 134-01049A Evaporative emission system tester |
|
|
1:49 B015 001 2:– Adapter (Part of 49 B015 0A0) |
|
1:49 B015 002 2:– Adapter (Part of 49 B015 0A0) |
|
1:49 N013 1A0D 2:– Fuel pressure gauge set |
|
|
1:49 N013 103A 2:– Remover (Part of 49 N013 1A0D) |
|
1:49 E042 001 2:– Remover |
|
1:49 T018 001 2:– O2 sensor wrench |
|
|
1: – 2: AKS042808 Adapter |
|
1: 49 0187 280A 2: – Oil pressure gauge |
|
1:49 E019 001 2:– Adapter |
|
|
1:49 D019 908 2:– Gauge (Part of 49 D019 9A2) |
|
1:49 D019 909 2:– Hose (Part of 49 D019 9A2) |
|
1:49 D019 910 2:– Adapter (Part of 49 D019 9A2) |
|
|
1:49 D019 911 2:– Adapter (Part of 49 D019 9A2) |
|
1:49 D019 914 2:– Adapter (Part of 49 D019 9A2) |
|
1:49 H019 002 2:– Adapter |
|
|
1:49 D019 913 2:– Adapter (Part of 49 D019 9A2) |
|
1:49 D015 001 2:– Box wrench |
|
1:49 L018 001 2:– A/F sensor, HO2S wrench |
|
Engine Removal/Installation [Skyactiv G 2.0]
WARNING:
A hot engine can cause severe burns. Turn off the engine and wait until it
is cool before servicing.
Fuel vapor is hazardous. It can very easily ignite, causing serious inj ...
Engine SST [Mzr 2.3 Disi Turbo]
1: Mazda SST number
2: Global SST number
Example
1:49 UN30 3328
2:303–328
Rear oil seal replacer
1:–
2:303–507
Crankshaft TDC timing ...
Other materials:
Filament Repair
1. Clean the filament using isopropyl alcohol.
2. Attach tape to both sides of the filament.
3. Using a small brush or marking pen, apply silver paint.
4. After 2—3 min, carefully remove the tape without damaging the applied
area.
CAUTION:
Do not operate the rear window defrost ...
Seat Weight Sensor Calibration [Two Step Deployment Control System]
CAUTION:
If any of the following work is performed, perform the seat weight sensor
calibration using the M-MDS.
Replacement with a new seat weight sensor
Replacement with a new seat weight sensor control module
Replacement with new passenger-side seat pa ...
Manifold Absolute Pressure (Map) Sensor/Intake Air Temperature (Iat) Sensor
No.2 Removal/Installation [Skyactiv G 2.0]
NOTE:
Because the IAT sensor No.2 is integrated in the MAP sensor, replacing the
IAT sensor No.2 includes replacement of the MAP sensor/IAT sensor No.2.
1. Remove the battery cover..
2. Disconnect the negative battery cable..
3. Disconnect the MAP sensor/IAT sensor No.2 connecto ...
