Mazda 3 Service Manual: Blind Spot Monitoring (Bsm) Control Module Inspection
1. Disconnect the negative battery cable.
2. Remove the rear combination light..
3. Remove the rear bumper..
4. Connect the negative battery cable..
5. Measure the voltage at each terminal is as indicated in the Terminal Voltage Tables.
-
If the voltage or continuity is not as specified in the Terminal Voltage Table, inspect the parts under “Inspection item (s)”.
-
If the system does not operate normally even though the related wiring harness and short cord are normal, replace the BSM control module.
Terminal Voltage Table (Reference)
BSM control module (LH)
|
Terminal |
Signal |
Connected to |
Measurement condition |
Voltage (V) |
Inspection item (s) |
|
|
A |
Ground |
Body ground |
Under any condition |
1.0 or less |
|
|
|
B |
Power supply |
METER 15 A fuse |
Switch the ignition ON |
B+ |
|
|
|
Switch the ignition OFF (LOCK) |
1.0 or less |
|||||
|
D |
BSM indicator light (LH) signal |
BSM indicator light (LH) |
Switch the ignition to ON |
LED off |
1.0 or less |
|
|
LED on |
B+ |
|||||
|
E |
Ground |
Body ground |
Under any condition |
1.0 or less |
|
|
|
G |
CAN_L |
CAN system related module |
Because this terminal is for communication, good/no good judgment by terminal voltage is not possible. |
|||
|
H |
CAN_H |
CAN system related module |
Because this terminal is for communication, good/no good judgment by terminal voltage is not possible. |
|||
BSM control module (RH)
|
Terminal |
Signal |
Connected to |
Measurement condition |
Voltage (V) |
Inspection item (s) |
|
|
A |
Ground |
Body ground |
Under any condition |
1.0 or less |
|
|
|
B |
Power supply |
METER 15 A fuse |
Switch the ignition ON |
B+ |
|
|
|
Switch the ignition OFF (LOCK) |
1.0 or less |
|||||
|
D |
BSM indicator light (RH) signal |
BSM indicator light (RH) |
Switch the ignition to ON |
LED off |
1.0 or less |
|
|
LED on |
B+ |
|||||
|
E |
BSM OFF switch signal |
BSM OFF switch |
Switch the ignition to ON |
BSM switch pressed |
1.0 or less |
|
|
BSM switch not pressed |
B+ |
|||||
|
G |
CAN_L |
CAN system related module |
Because this terminal is for communication, good/no good judgment by terminal voltage is not possible. |
|||
|
H |
CAN_H |
CAN system related module |
Because this terminal is for communication, good/no good judgment by terminal voltage is not possible. |
|||
Blind Spot Monitoring (Bsm) Bracket Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the rear combination light..
3. Remove the rear bumper..
4. Remove the BSM control module..
5. Remove the nuts.
6. Remove the clip.
...
Blind Spot Monitoring (Bsm) Control Module Removal/Installation
CAUTION:
If the BSM control modules are installed with the left and right modules
reversed, a DTC will be displayed and system will enter the fail-safe function.
Therefore, confirm that ...
Other materials:
Rear Door Module Panel Removal/Installation
1. Fully open the rear door glass.
2. Disconnect the negative battery cable..
3. Remove the following parts:
a. Rear door trim.
b. Rear door speaker.
c. Rear power window motor.
d. Rear door quarter glass.
e. Rear door glass.
4. Remove the clips securing the rear door wiring harness ...
Seat Weight Sensor Inspection [Two Step Deployment Control System]
CAUTION:
If any of the following work is performed, perform the seat weight sensor
inspection using the M-MDS.
Removal of the passenger-side seat
Loosening and retightening of passenger’s seat fixing bolts
Or, the vehicle is involved in a collision
...
No.7 Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing
Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot
Monitoring (Bsm)]
7
BSM indicator light does not flash while under BSM indicator light-flashing
conditions (with combination switch operation (turn signal switch))
Description
The BSM indicator light does not flash or illuminate continuously,
...
