Mazda 3 Service Manual: Fuel Gauge Sender Unit Inspection
MZR 2.3 DISI Turbo, SKYACTIV-G 2.0
NOTE:
-
The fuel gauge sender unit is integrated with the fuel pump unit.
1. Disconnect the negative battery cable..
2. Remove the rear seat cushion..
3. Remove the fuel pump unit..
4. Verify that the resistance between terminals A and C of the fuel gauge sender unit based on the height of the float as shown in the figure.
-
If they are not as shown in the figure, replace the fuel pump unit.
|
Float height (mm {in}) |
Resistance (ohms) |
|
165.6 {6.520} |
9.5—12.5 |
|
159.3 {6.272} |
20.0 |
|
130.1 {5.122} |
109.4 |
|
91.3 {3.59} |
194.8—222.2 |
|
52.2 {2.06} |
307.6 |
|
25.7 {1.01} |
400.0 |
|
20.0 {0.787} |
414.5—405.5 |
MZR 2.0, MZR 2.5
NOTE:
-
The fuel gauge sender unit is integrated with the fuel pump unit.
1. Disconnect the negative battery cable..
2. Remove the rear seat cushion..
3. Remove the fuel pump unit..
4. Verify that the resistance between terminals B and D of the fuel gauge sender unit based on the height of the float as shown in the figure.
-
If they are not as shown in the figure, replace the fuel pump unit.
|
Float height (mm {in}) |
Resistance (ohms) |
|
168.5 {6.634} |
18—22 |
|
130.1 {5.122} |
107.2—111.6 |
|
91.3 {3.59} |
206—211 |
|
52.2 {2.06} |
304.6—310.6 |
|
40.6 {1.60} |
333.5—339.5 |
|
12.1 {0.476} |
396.8—403.2 |
Fan Switch Inspection [Manual Air Conditioner]
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Upper panel.
b. Shift lever knob (MTX).
c. Selector lever knob (ATX).
d. Shift panel.
e. Side wall.
f. Consol ...
Fuel Gauge Sender Unit Removal/Installation
MZR 2.0, MZR 2.5
NOTE:
Fuel pump unit cannot be disassembled.
1. Remove the fuel gauge sender unit..
MZR 2.3 DISI Turbo
NOTE:
Fuel pump unit cannot be disassembled.
1. ...
Other materials:
DRL (Daytime Running Light) Bulb Removal/Installation
MZR 2.0, MZR 2.5, MZR 2.3 DISI Turbo
1. Disconnect the negative battery cable..
2. Disconnect the connector.
3. Rotate the DRL bulb in the direction of the arrow shown in the figure to remove
it.
4. Remove the DRL bulb.
5. Install in the reverse order of removal.
SKYACTIV-G 2.0
...
Oil Pressure Switch Removal/Installation [FS5 A EL]
WARNING:
A hot transaxle and ATF can cause severe burns. Turn off the engine and wait
until they are cool.
1. Perform the following procedures.
a. Remove the battery cover..
b. Disconnect the negative battery cable.
c. Remove the aerodynamic under cover NO.2..
2. Remove in t ...
Front ABS Wheel Speed Sensor Removal/Installation
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. After installation, verify that there is no twisting in the front ABS wheel-speed
sensor.
1
Connector
2
Front ABS wheel-speed sensor
...
