Mazda 3 manuals

Mazda 3 Service Manual: No.7 Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]

Mazda 3 Service Manual / Body / Lighting & Horn / Exterior / No.7 Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]


7

BSM indicator light does not flash while under BSM indicator light-flashing conditions (with combination switch operation (turn signal switch))

Description

  • The BSM indicator light does not flash or illuminate continuously, but the conditions to flash the BSM indicator light are satisfied (vehicle speed above 32 km/h {20 mph} or more, turn signal on, and vehicle in warning zone).

  • BSM indicator light does not flash or illuminate continuously, but turn signals are off.

Possible Causes

NOTE:

  • This malfunction symptom is basically the same as symptom “No.5 BSM indicator light does not illuminate while under BSM indicator light-illumination conditions”.

  • The BSM control module mistakenly recognizes a vehicle as being outside of the warning zone when it is actually inside of it.

    • Radar (BSM control module integrated) is not emitted inside of warning zone (unable to emit radar inside warning zone)

      • Damage, deformity or looseness to installation bracket or vehicle frame (including moderate impacts).

      • Malfunction in steering angle signal (communication error between BCM and BSM control module, or steering angle sensor malfunction).

      • Problem with rear bumper such as soiling to radar emitting/receiving area, application of stickers (including transparent types), repairs using putty application.

    • BSM control module does not receive echo-back correctly

      • BSM control module (radar) malfunction

      • Problem with rear bumper such as soiling to radar emitting/receiving area, application of stickers (including transparent types), repairs using putty application.

        NOTE:

        • Rear bumper problems such defective installation of rear bumper, excessive soiling on radar emitting/receiving area, sticker adhesion (including transparent types), repairs to rear bumper using putty

        • Non-genuine bumper or paint, or installation of after-market parts negatively affecting radar echo-back ability

    • After-market electrical parts interfere with BSM system

  • BSM does not recognize vehicle speed correctly (BSM control module mistakenly recognizes vehicle speed as being within 32 km/h {20 mph} or more

    • PCM communication error with BSM control module

    • Malfunction in ABS wheel speed sensor related parts

  • Malfunction in BSM indicator light related parts

    • Open circuit in wiring harness between BSM indicator light and BSM control module

    • Open circuit in wiring harness or poor ground between BSM control module and ground

    • BSM indicator light malfunction

  • Signal is not input for turn signal

    • Combination switch (turn signal switch) malfunction

    • Open circuit in wiring harness between combination switch (turn signal switch) and BCM

    • Communication error between BCM and BSM control module

    • BSM control module malfunction


Diagnostic Procedure

Step

Inspection

Result

Action

1

    VERIFY MALFUNCTION SYMPTOM

  • BSM indicator light illuminates while under light-off conditions.

Yes

Go to the next step.

No

Go to the symptom troubleshooting procedure,”No.5 BSM indicator light does not illuminate while under BSM indicator light-illumination conditions”.

(See NO.5 BSM INDICATOR LIGHT DOES NOT ILLUMINATE WHILE UNDER BSM INDICATOR LIGHT-ILLUMINATION CONDITIONS [BLIND SPOT MONITORING (BSM)].)

2

    VERIFY DTCs

  • Retrieve DTCs from the BSM control module, BCM, DSC HU/CM, PCM, and TCM using the M-MDS.

    (See DTC INSPECTION [BLIND SPOT MONITORING (BSM)].)

    (See DTC INSPECTION [BCM].)

    (See ON-BOARD DIAGNOSTIC TEST [MZR 2.0, MZR 2.5].)

    (See ON-BOARD DIAGNOSTIC TEST [MZR 2.3 DISI Turbo].)

    (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 2.0].)

    (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)

    (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FW6A-EL].)

  • Are any DTCs displayed?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [BLIND SPOT MONITORING (BSM)].)

(See DTC TABLE [BCM].)

(See DTC TABLE [MZR 2.0, MZR 2.5].)

(See DTC TABLE [MZR 2.3 DISI Turbo].)

(See DTC TABLE [SKYACTIV-G 2.0].)

(See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [FW6A-EL].)

(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)

No

Go to the next step.

3

    INSPECT IF MALFUNCTION IS IN BCM INPUT SIGNAL OR BCM

  • Monitor the following PIDs on the suspected side of the BSM control module using the M-MDS.

    (See PID/DATA MONITOR INSPECTION [BLIND SPOT MONITORING (BSM)].)

    • TURN_SW_L

    • TURN_SW_R

  • Are the monitoring values normal?

Yes

Replace the BSM control module.

(See BLIND SPOT MONITORING (BSM) CONTROL MODULE REMOVAL/INSTALLATION.)

No

Go to the next step.

4

    INSPECT TURN SIGNAL SWITCH SIGNAL

  • Monitor the following BCM PIDs using the M-MDS:

    (See PID/DATA MONITOR INSPECTION [BCM].)

    • TURN_SW_L

    • TURN_SW_R

  • Are the monitoring values normal?

Yes

Replace the BSM control module.

(See BLIND SPOT MONITORING (BSM) CONTROL MODULE REMOVAL/INSTALLATION.)

No

  • Inspect the following. If a malfunction is detected, repair or replace the malfunctioning part.

    • Combination switch (turn signal switch)

    • Wiring harness between combination switch (turn signal switch) and BCM for short to ground circuit

      (See LIGHT SWITCH INSPECTION.)

  • If a malfunction is not detected, replace the BCM.

    (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION.)


No.6 Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
6 BSM indicator light flashes while not under BSM indicator light-flashing conditions (no combination switch operation (turn signal switch) Description ...

Interior
...

Other materials:

Exterior Care
The paintwork on your Mazda represents the latest technical developments in composition and methods of application. Environmental hazards, however, can harm the paint's protective properties, if proper care is not taken. Here are some examples of possible damage, with tips on how to preve ...

Buckle Switch Inspection
Driver Side 1. Switch the ignition to off. 2. Disconnect the negative battery cable.. 3. Remove the front seat.. 4. Remove the front buckle.. 5. Inspect for continuity between the buckle switch terminals using a tester. If not as indicated in the table, replace the driver sid ...

Sunroof Switch Inspection
NOTE: The sunroof switch is together with the front map light. 1. Disconnect the negative battery cable.. 2. Remove the map light from the headliner.. 3. Inspect for continuity between the sunroof switch terminals using an ohmmeter. If not as specified, replace the sun ...

© 2016-2019 Copyright www.mazda3tech.com