Mazda 3 Service Manual: Exterior
- Afs (Adaptive Front Lighting System) Control Module Removal/Installation
- Afs (Adaptive Front Lighting System) Off Switch Inspection
- Afs (Adaptive Front Lighting System) Off Switch Removal/Installation
- Back Up Light Bulb Removal/Installation
- Brake/Taillight Bulb Removal/Installation
- DRL (Daytime Running Light) Bulb Removal/Installation
- Discharge Headlight Control Module Removal/Installation
- Discharge Headlight Service Warnings
- Discharge Headlight System Inspection
- Front Combination Light Bracket Replacement
- Front Combination Light Removal/Installation
- Front Fog Light Aiming
- Front Fog Light Bulb Removal/Installation
- Front Fog Light Relay Removal/Installation
- Front Fog Light Removal/Installation
- Front Side Marker/Front Turn Light Bulb Removal/Installation
- Headlight Aiming
- Headlight Auto Leveling System Initialization
- Headlight Bulb Removal/Installation
- Headlight Leveling Actuator Inspection
- High Mount Brake Light Bulb Removal/Installation
- High Mount Brake Light Disassembly/Assembly
- High Mount Brake Light Removal/Installation
- License Plate Light Bulb Removal/Installation
- License Plate Light Removal/Installation
- PID/Data Monitor Inspection [Afs (Adaptive Front Lighting System)]
- Parking Light Bulb Removal/Installation
- Parking/Front Side Marker/Front Turn Light Bulb Removal/Installation
- Rear Combination Light Removal/Installation
- Back Up Light Switch Inspection
- Back Up Light Switch Removal/Installation [A26 M R]
- Back Up Light Switch Removal/Installation [C66 M R]
- Back Up Light Switch Removal/Installation [G35 M R]
- Back Up Light Switch Removal/Installation [G66 M R]
- Combination Switch Disassembly/Assembly
- Combination Switch Removal/Installation
- Front Fog Light Switch Inspection
- Hazard Warning Switch Inspection
- Hazard Warning Switch Removal/Installation
- Headlight Leveling Switch Inspection
- Headlight Leveling Switch Removal/Installation
- No.6 Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- No.7 Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
Light Switch Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the column cover..
3. Disconnect the connector.
4. Remove the screws shown in the figure, then remove the light switch by pulling
it in ...
Afs (Adaptive Front Lighting System) Control Module Removal/Installation
NOTE:
Perform the auto leveling system initialization after newly replacing the
AFS control module to assure that the auto leveling system operates correctly.
1. Disconnect the negati ...
Other materials:
Maintenance of the Active Driving
Display
The combiner and mirror surface have a
special coating. When cleaning, do not use
a hard or rough-surface cloth, or cleaning
detergent. In addition, if a chemical
solvent gets on the active driving display,
wipe it off immediately. Otherwise, the
combiner and mirror could be damaged
and the s ...
Base Installation
1. Cut away all of the original sealant using a razor.
WARNING:
Using a razor with bare hands can cause injury. Always wear gloves when using
a razor.
2. Clean and degrease the ceramic coating on the glass and the base.
CAUTION:
Keep the area free of dirt and grease, and ...
Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Standard Deployment
Control System]
WARNING:
A live (undeployed) air bag module or pre-tensioner seat belt may accidentally
operate (deploy) when it is disposed of and cause serious injury. Do not dispose
of a live (undeployed) air bag module and pre-tensioner seat belt. If the SSTs
(Deployment tool and Adapter harn ...
