Mazda 3 manuals

Mazda 3 Owners Manual: Security Setting (Type A)

If a passcode is set, the system cannot be activated unless the passcode is input.

NOTE Do this function only when parked. It is too distracting to attempt while driving and you may make too many errors to be effective.

Passcode setting

  1. Press the pick-up button or talk button with a short press.
  2. Say: [Beep] “Setup”
  3. Prompt: “Select one of the following: Pairing options, confirmation prompts, language, passcode, select phone or select music player.”
  4. Say: [Beep] “Passcode”
  5. Prompt: “Passcode is disabled. Would you like to enable it?”
  6. Say: [Beep] “Yes”
  7. Prompt: “Please say a 4-digit passcode. Remember this passcode. It will be required to use this system.”
  8. Say: [Beep] “XXXX” (Say a desired 4-digit passcode, “PCode”.)
  9. Prompt: “Passcode XXXX (Passcode, PCode). Is this correct?”
  10. Say: [Beep] “Yes”
  11. Prompt: “Passcode is enabled.”

Using Bluetooth ® Hands-Free with a passcode

  1. Press the pick-up button or talk button with a short press.
  2. Prompt: “Hands-Free system is locked. State the passcode to continue.”
  3. Say: [Beep] “XXXX” (Say the set passcode “PCode”.)
  4. If the correct passcode is input, voice guidance “XXXXXX... (Ex. “Mary's device”) (Device tag) is connected” is announced.

    If the passcode is incorrect, voice guidance “XXXX (4-digit passcode, Pcode) incorrect passcode, please try again” is announced.

Canceling the passcode

NOTE Do this function only when parked. It is too distracting to attempt while driving and you may make too many errors to be effective.

  1. Press the pick-up button or talk button with a short press.
  2. Say: [Beep] “Setup”
  3. Prompt: “Select one of the following: Pairing options, confirmation prompts, language, passcode, select phone or select music player.”
  4. Say: [Beep] “Passcode”
  5. Prompt: “Passcode is enabled. Would you like to disable it?”
  6. Say: [Beep] “Yes”
  7. Prompt: “Passcode is disabled.”

Confirmation Prompts

The confirmation prompt confirms the command content to the user before advancing to the operation requested by the user. When this function is turned on, the system reads out the voice input command previously received and confirms whether the command is correct before advancing to the command execution.

When the confirmation prompt function is turned on: (Ex. “Calling John's device. Is this correct?”) When the confirmation prompt function is turned off: (Ex. “Calling John's device.”)

NOTE If the confirmation prompt function is turned off when making an emergency call, the system reads out and confirms the command before executing it.

  1. Press the pick-up button or talk button with a short press.
  2. Say: [Beep] “Setup”
  3. Prompt: “Select one of the following: Pairing options, confirmation prompts, language, passcode, select phone or select music player.”
  4. Say: [Beep] “Confirmation prompts”
  5. Prompt: “Confirmation prompts are on/off. Would you like to turn confirmation prompts off/on?”
  6. Say: [Beep] “Yes”
  7. Prompt: “Confirmation prompts are off/on.”
Voice Recognition (Type A)
In this section, the basic operation of the voice recognition is explained. Activating Voice Recognition To Activate the Main Menu: Press the pick-up button or talk button with a short press. En ...

Voice Recognition Learning Function (Speaker Enrollment) (Type A)
The voice recognition learning function enables voice recognition appropriate to the characteristics of the user's voice. If the recognition of the voice input commands to the system is not adequa ...

Other materials:

EGR Valve Removal/Installation [Mzr 2.0, Mzr 2.5]
1. Remove the battery cover.. 2. Disconnect the negative battery cable.. 3. Drain the engine coolant from the radiator.. 4. Remove the air cleaner and the air hose as a single unit.. 5. Remove the radiator hose (upper, engine side).. 6. Disconnect the EGR valve connector. 7. Remove in th ...

Pressure Sensor Removal/Installation [Two Step Deployment Control System]
1. Switch the ignition to off. 2. Disconnect the negative battery cable and wait for 1 min or more.. 3. Remove the inner garnish.. 4. Remove the front door trim.. 5. Remove the bolts. 6. Remove the pressure sensor. 7. Disconnect the connector from the pressure sensor by pressing the ...

Brake Hose (Front) Removal/Installation [Mzr 2.0, Skyactiv G 2.0, Mzr 2.5]
1. Remove in the order indicated in the table. 2. Install in the reverse order of removal. 3. Add brake fluid, bleed the brakes, and inspect for leakage after the installation has been completed.. 1 Brake pipe 2 Clip 3 ...

© 2016-2018 Copyright www.mazda3tech.com