Mazda 3 Service Manual: Basic Inspection [FS5 A EL]
|
STEP |
INSPECTION |
ACTION |
|
|
1 |
Measure the battery voltage. Is the battery voltage 10.0—14.0 V? |
Yes |
Go to the next step. |
|
No |
Replace or recharge the battery. (See BATTERY RECHARGING [MZR 2.0, MZR 2.5].) |
||
|
2 |
Inspect the TCM related harnesses, connectors and fuses. Are they normal? |
Yes |
Go to the next step. |
|
No |
Repair or replace any malfunctioning parts according to the inspection result. |
||
|
3 |
Switch the ignition to ON. When the selector lever is moved, does the gear position indicator light indication correspond to the selector lever position? Also, when other positions are selected from N or P during idling, does the vehicle move within 1—2 s ? |
Yes |
Go to the next step. |
|
No |
Inspect the selector lever and TR switch. Repair or replace malfunctioning parts. (See SELECTOR LEVER INSPECTION.) (See TRANSAXLE RANGE (TR) SWITCH INSPECTION [FS5A-EL].) If the selector lever and TR switch are normal, go to the next step. |
||
|
4 |
Perform the road test. (See ROAD TEST [FS5A-EL].) Is the ATX operating normally? |
Yes |
Go to the next step. |
|
No |
Repair or replace any malfunctioning parts according to the inspection result. |
||
|
5 |
Inspect the ATF color and condition. (See AUTOMATIC TRANSAXLE FLUID (ATF) INSPECTION [FS5A-EL].) Are the ATF color and odor normal? |
Yes |
Go to the next step. |
|
No |
Repair or replace any malfunctioning parts according to the inspection result. Flush the ATX and cooler line if necessary. |
||
|
6 |
Perform the line pressure test. (See MECHANICAL SYSTEM TEST [FS5A-EL].) Is the line pressure normal? |
Yes |
Go to the next step. |
|
No |
Repair or replace any malfunctioning parts according to the inspection result. |
||
|
7 |
Perform the stall test. (See MECHANICAL SYSTEM TEST [FS5A-EL].) Is the stall speed normal? |
Yes |
Go to the next step. |
|
No |
Repair or replace any malfunctioning parts according to the inspection result. |
||
|
8 |
Perform the time lag test. (See MECHANICAL SYSTEM TEST [FS5A-EL].) Is the time lag within the specified? |
Yes |
Go to the next step. |
|
No |
Repair or replace any malfunctioning parts according to the inspection result. |
||
|
9 |
Inspect the value at the following PCM and TCM PIDs using the M-MDS. (See PCM INSPECTION [MZR 2.0, MZR 2.5].) (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FS5A-EL].)
Are the PID values normal? |
Yes |
Perform the symptom troubleshooting and follow the procedures. |
|
No |
Repair or replace any malfunctioning parts according to the inspection result. |
||
Automatic Transaxle Shift Mechanism Removal/Installation
Selector Lever Removal/Installation
1. Remove the battery cover..
2. Disconnect the negative battery cable..
3. Remove in the order indicated in the table.
4. Install in the reverse order of r ...
Control Valve Body Removal/Installation [FS5 A EL]
Primary Control Valve Body On-Vehicle Removal
WARNING:
A hot transaxle and ATF can cause severe burns. Turn off the engine and wait
until they are cool.
Using compressed air can ca ...
Other materials:
Keyless Control Module Configuration
1. Connect the M-MDS (IDS) to DLC-2.
2. After the vehicle is identified, select the following items from the initialization
screen of the IDS.
Select “Module Programming”.
3. Then, select items from the screen menu in the following order.
Select “Programmable Module Ins ...
Fuel Requirements
Vehicles with catalytic converters or oxygen sensors must use ONLY UNLEADED
FUEL,
which will reduce exhaust emissions and keep spark plug fouling to a minimum.
This vehicle will perform best with fuel listed in the table.
* U.S. federal law requires that octane ratings be posted on gasoli ...
Precaution [ABS]
1. Any one or a combination of the ABS warning and brake system warning lights
illuminates even when the system is normal.
Warning lights that may illuminate and/or flash
Cases in which the light may illuminate
Conditions in which the light will go ou ...
