Mazda 3 Service Manual: Automatic
- Automatic Transaxle Fluid (ATF) Adjustment [Fw6 A EL]
- Automatic Transaxle Fluid (ATF) Inspection [FS5 A EL]
- Automatic Transaxle Fluid (ATF) Inspection [Fw6 A EL]
- Automatic Transaxle Fluid (ATF) Replacement [FS5 A EL]
- Automatic Transaxle Fluid (ATF) Replacement [Fw6 A EL]
- Automatic Transaxle Removal/Installation [FS5 A EL]
- Automatic Transaxle Removal/Installation [Fw6 A EL]
- Automatic Transaxle Shift Mechanism Removal/Installation
- Basic Inspection [FS5 A EL]
- Control Valve Body Removal/Installation [FS5 A EL]
- Control Valve Body Removal/Installation [Fw6 A EL]
- Coupler Component Removal/Installation [Fw6 A EL]
- Down Switch Inspection [FS5 A EL]
- Down Switch Inspection [Fw6 A EL]
- Drive Plate Removal/Installation [FS5 A EL]
- Drive Plate Removal/Installation [Fw6 A EL]
- Electric Power Steering Oil Pump Component Disassembly/Assembly
- Electric Power Steering Oil Pump Component Removal/Installation
- Initial Learning [Fw6 A EL]
- Intermediate Sensor Inspection [FS5 A EL]
- Intermediate Sensor Removal/Installation [FS5 A EL]
- Joint Shaft Assembly [Mzr 2.5 (ATX)]
- Judder Upon Torque Converter Clutch (TCC) Operation [Fw6 A EL]
- Key Interlock System Inspection
- M Position Switch Inspection [FS5 A EL]
- M Position Switch Inspection [Fw6 A EL]
- Neutral Switch Removal/Installation [A26 M R]
- Neutral Switch Removal/Installation [C66 M R]
- Neutral Switch Removal/Installation [G35 M R]
- Neutral Switch Removal/Installation [G66 M R]
- No.12 Torque Converter Clutch (TCC) Non Operation [FS5 A EL]
- No.16 Judder Upon Torque Converter Clutch (TCC) Operation [FS5 A EL]
- Oil Pump Removal/Installation [Mzr 2.0, Mzr 2.5]
- Oil Pump Removal/Installation [Mzr 2.3 Disi Turbo]
- Oil Pump Removal/Installation [Skyactiv G 2.0]
- Oil Seal (Control Valve Body) Replacement [Fw6 A EL]
- On/Off Solenoid Removal/Installation [Fw6 A EL]
- Pilot Bearing Inspection [A26 M R]
- Pilot Bearing Inspection [C66 M R]
- Pilot Bearing Inspection [G35 M R]
- Pilot Bearing Inspection [G66 M R]
- Selector Lever Inspection
- Shift Lock System Inspection
- Solenoid Valve Inspection [FS5 A EL]
- Solenoid Valve Removal/Installation [FS5 A EL]
- Starter Interlock Switch Inspection [Mzr 2.0, Mzr 2.5]
- Starter Interlock Switch Inspection [Mzr 2.3 Disi Turbo]
- Starter Interlock Switch Inspection [Skyactiv G 2.0]
- Starter Interlock Switch Removal/Installation [C66 M R]
- TCM Configuration [Fw6 A EL]
- TCM Inspection [FS5 A EL]
- TCM Removal/Installation [FS5 A EL]
- Torque Converter Clutch (TCC) Non Operation [Fw6 A EL]
- Transmission/Transaxle SST
- Up Switch Inspection [FS5 A EL]
- Up Switch Inspection [Fw6 A EL]
Transaxle Range (TR) Switch Removal/Installation [FS5 A EL]
CAUTION:
Water or foreign objects entering the connector can cause a poor connection
or corrosion. Be sure not to drop water or foreign objects on the connector
when disconnecting it.
...
Automatic Transaxle Fluid (ATF) Adjustment [Fw6 A EL]
CAUTION:
Only adjust the ATF level when the ATF temperature is 45—55 °C {113—131 °F}.
If the ATF level is incorrect, it could damage the transaxle.
Do not add ATF over the spe ...
Other materials:
HVAC SST
49 B061 014
Spring Lock Coupling Disconnect Tool
49 G061 001
Spring Lock Coupling Disconnect Tool
49 B061 015A
Holder
49 0839 425C
Bearing puller set
49 SE01 160 ...
Manifold Absolute Pressure (Map) Sensor/Intake Air Temperature (Iat) Sensor
No.2 Removal/Installation [Skyactiv G 2.0]
NOTE:
Because the IAT sensor No.2 is integrated in the MAP sensor, replacing the
IAT sensor No.2 includes replacement of the MAP sensor/IAT sensor No.2.
1. Remove the battery cover..
2. Disconnect the negative battery cable..
3. Disconnect the MAP sensor/IAT sensor No.2 connecto ...
Drive Belt Inspection [Mzr 2.0, Mzr 2.5]
MZR 2.0
A/C drive belt
NOTE:
Drive belt deflection/tension inspection is not necessary because of the
use of the maintenance-free type A/C drive belt.
Replace the drive belt if it is found to be damaged during visual inspection,
or if there is a malfunction or noise in th ...
