Mazda 3 Service Manual: Engine SST [Mzr 2.3 Disi Turbo]
1: Mazda SST number
2: Global SST number
Example
|
1:49 UN30 3328 2:303–328 Rear oil seal replacer |
|
|
1:– 2:303–507 Crankshaft TDC timing pin |
|
1:49 UN30 310610 2:303–1061 Camshaft alignment timing tool |
|
1:49 UN20 507202 2:205–07202 Crankshaft holding tool pins |
|
|
1:49 UN20 5072 2:205–072 Holder |
|
1:49 C017 5A0 2: – Engine support set |
|
1:49 H010 401 2:– Oil seal installer |
|
|
1:49 UN30 3328 2:303–328 Rear oil seal replacer |
|
1:49 D032 316 2: – Protractor |
|
1:49 B015 001 2:– Adapter (Part of 49 B015 0A0) |
|
|
1:49 B015 002 2:– Adapter (Part of 49 B015 0A0) |
|
1: 49 N013 103A 2:– Remover (Part of 49 N013 1A0D) |
|
1:49 G013 101 2:– Remover |
|
|
1:49 N013 1A0D 2:– Fuel pressure gauge set |
|
1:49 H080 740A 2: – Pressure tester |
|
1:49 0187 280A 2:– Oil pressure gauge |
|
|
1:49 E019 001 2:– Adapter |
|
1:49 D019 909 2:– Hose (Part of 49 D019 9A2) |
|
1:49 D019 910 2:– Adapter (Part of 49 D019 9A2) |
|
|
1:49 D019 911 2:– Adapter (Part of 49 D019 9A2) |
|
1:49 D019 914 2:– Adapter (Part of 49 D019 9A2) |
|
1:49 H019 002 2:– Adapter |
|
|
1:49 D019 913 2:– Adapter (Part of 49 D019 9A2) |
|
1:49 D019 908 2:– Gauge (Part of 49 D019 9A2) |
|
1:49 G040 001 2:– Handle |
|
|
1:49 G040 002 2:– Installer |
|
1:49 E042 001 2:– Remover |
|
1: – 2:134-01049A Evaporative emission system tester |
|
|
1:– 2:AKS042808 Adapter |
|
1:49 L018 002 2:– Serrated bit |
|
1:49 T018 001 2:– O2 sensor wrench |
|
|
1:49 L018 001 2:– O2 sensor wrench |
|
1:49 D015 001 2:– Box wrench |
|
1:49 G010 4A0 2:– Tensioner release tool set |
|
Engine SST [Mzr 2.0, Mzr 2.5]
1: Mazda SST number
2: Global SST number
Example
1:49 UN01 052
2:310–D005
Spring lock coupler tool (green)
1: 49 C017 5A0
2: –
En ...
Engine SST [Skyactiv G 2.0]
1: Mazda SST number
2: Global SST number
Example
1:49 UN20 5072
2:205–072
Holder
1: –
2: 134-01049A
Evaporative emission system t ...
Other materials:
Inside Trunk Release Lever
(4-Door)
Your vehicle is equipped with an inside
trunk release lever that provides a means
of escape for children and adults in the
event they become locked inside the trunk.
No matter how careful adults might be
with keys and locking their cars, parents
should be aware that children may be
tempted ...
Rear Spoiler Removal/Installation
4SD
1. Remove the trunk lid trim..
2. Remove the nuts.
3. While cutting the double-sided adhesive tape using a flathead screwdriver
or a razor, separate the rear spoiler from the trunk lid.
WARNING:
Using a razor with bare hands can cause injury. Always wear gloves when usin ...
Front Lower Arm Removal/Installation
CAUTION:
Performing the following procedures without first removing the ABS wheel-speed
sensor may possibly cause an open circuit in the wiring harness if it is pulled
by mistake. Before performing the following procedures, disconnect the ABS wheel-speed
sensor wiring harness connec ...
