Mazda 3 Service Manual: Front Drain Hose Installation
CAUTION:
-
If the front drain hose is pinched or bent anywhere, the water in the hose may not discharge and enter the inside of the vehicle. During and after installation of the trims and the headliner, always make sure there is no interference with the front drain hose. Fix any problem if found.
1. Apply soapy water to the front drain hose inserting area.
2. Insert one end (the wider end) of the front drain hose into the sunroof frame.
3. Install the front drain hose to the clips, parallel to the pillar and free of slack.
4. Insert the front drain hose joint into the hinge pillar inner hole.
5. Connect the auto-dimming mirror connector. (vehicles with auto-dimming mirror)
6. Install the following parts:
a. Headliner.
b. Assist handle.
c. Sunvisor.
d. Map light.
e. C-pillar trim.
f. Trunk side upper trim (5HB).
g. Tire house trim.
h. Rear seat cushion.
i. B-pillar upper trim.
j. Upper anchor of the front seat belt.
k. B-pillar lower trim.
l. Rear scuff plate.
m. A-pillar trim.
n. Sunroof seaming welt
o. Dashboard.
p. Windshield wiper motor.
q. Cowl grille.
r. Front fender molding.
s. Windshield wiper arm and blade.
t. A-pillar trim.
u. multi information display (with multi information display).
v. Information display (with information display).
w. Hole cover.
x. Dashboard upper panel.
y. Center cover.
z. Instrument cluster.
aa. Climate control unit.
ab. Audio unit.
ac. Center panel.
ad. Steering shaft.
ae. Joint cover.
af. Combination switch.
ag. Column cover.
ah. Steering wheel.
ai. Driver-side air bag module.
aj. Knee bolster.
ak. Lower panel.
al. Hood release lever from the lower panel.
am. Selector lever component (ATX).
an. Shift lever component (MTX).
ao. Console.
ap. Side wall.
aq. Shift panel.
ar. Selector lever knob (ATX).
as. Shift lever knob (MTX).
at. Upper panel.
au. Glove compartment.
av. Dashboard under cover.
aw. Front side trim.
ax. Front scuff plate.
ay. Front doors.
7. Connect the rain sensor connector. (Vehicles with auto light / wiper system)
8. Install the rain sensor cover. (Vehicles with auto light / wiper system).
9. Install the seaming welt.
10. Connect the negative battery cable..
Deflector Removal/Installation
1. Fully open the glass panel.
2. Press the spring in the direction shown by the arrow and remove it from the
hook.
3. Remove the deflector.
4. Install in the reverse order of removal. ...
Front Drain Hose Removal
1. Set the air intake mode to FRESH.
2. Set the air mix mode to MAX COLD.
3. Disconnect the negative battery cable.
4. Remove the rain sensor cover. (Vehicles with auto light / wiper system).
...
Other materials:
Spare Tire
Your Mazda has a temporary spare tire.
The temporary spare tire is lighter and
smaller than a conventional tire, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spare tires should
NEVER be used for long drives or
extended periods.
WAR ...
Blind Spot Monitoring (Bsm) Control Module Removal/Installation
CAUTION:
If the BSM control modules are installed with the left and right modules
reversed, a DTC will be displayed and system will enter the fail-safe function.
Therefore, confirm that the left/right BSM control modules are installed correctly.
1. Disconnect the negative battery ...
Map Light Inspection
1. Disconnect the negative battery cable..
2. Remove the map light..
3. Verify that the continuity between the map light terminals is as indicated
in the table.
If not as indicated in the table, inspect the bulb. If there is no malfunction,
replace the map light.
4. ...
