Mazda 3 manuals

Tesla Model 3 2017-2022 Owner's Manual: Removing the Maintenance Panel

To check fluid levels, remove the maintenance panel:

  1. Open the hood.
  2.  Pull the maintenance panel upward to release the clips that hold it in place.

Removing the Maintenance Panel


  1. If checking the Battery coolant, remove the cabin intake trim panel by pulling it upwards to release the clips that hold it in place.

Caution: The maintenance panel protects the front trunk from water. When reattaching, make sure it is fully seated.

Checking Battery Coolant

Your Battery coolant should not need to be replaced for the life of your vehicle under most circumstances. However, if the quantity of fluid in the cooling system drops below the recommended level, the touchscreen displays a warning message. Stop driving Model 3 as soon as safety permits and contact Tesla.

Fluid Level Check

DO NOT REMOVE THE FILLER CAP AND DO NOT ADD FLUID. Doing so can result in damage not covered by the warranty.

Do Not Top Up Battery Coolant

Warning: Battery coolant can be hazardous and can irritate eyes and skin.

Under no circumstances should you remove the filler cap and/or add coolant.

If the touchscreen warns you that the fluid level is low, contact Tesla immediately.

To maximize the performance and life of the Battery, the cooling system uses a specific mixture of G-48 ethylene-glycol coolant (HOAT). Contact Tesla for more specific information about the coolant.

Checking Brake Fluid

Warning: Contact Tesla immediately if you notice increased movement of the brake pedal or a significant loss of brake fluid.

Driving under these conditions can result in extended stopping distances or complete brake failure.

A red brake indicator on the
touchscreen alerts you if the quantity of fluid in the brake reservoir drops below the recommended level. If it displays while driving, stop as soon as safety permits by gently applying the brakes. Do not continue driving.

Contact Tesla immediately.

Topping Up the Brake Fluid

Do not top up your brake fluid. The following instructions are provided for information purposes and future reference only:

  1. Clean the filler cap before removing it to prevent dirt from entering the reservoir.
  2.  Unscrew the cap and remove it.
  3.  Top up the reservoir to the MAX mark using the appropriate brake fluid.
  4. Replace the filler cap, ensuring it is fully secured.

Warning: Only use new fluid from a sealed air-tight container. Never use previously used fluid or fluid from a previously opened container-fluid absorbs moisture which decreases braking performance.

Warning: Brake fluid is highly toxic. Keep containers sealed and out of the reach of children. In the event of accidental consumption, seek medical attention immediately.

Caution: Brake fluid damages painted surfaces. Immediately soak up any spills with an absorbent cloth and wash the area with a mixture of car shampoo and water.

Fluid Reservoirs
...

Topping Up Windshield Washer Fluid
The only reservoir into which you can add fluid is the windshield washer fluid reservoir, which is located behind the front trunk. When the level is low, a message displays on the touchscreen. ...

Other materials:

Washer Fluid
Inspecting Washer Fluid Level WARNING Use only windshield washer fl uid or plain water in the reservoir: Using radiator antifreeze as washer fl uid is dangerous. If sprayed on the windshield, it will dirty the windshield, aff ect your visibility, and could result in an a ...

Spark Plug Inspection [Mzr 2.0, Mzr 2.5]
Specification Spark plug type LFJD-18110, L3Y2-18110 Plug Gap Inspection CAUTION: To avoid possible damage to the tip, do not adjust the spark plug gap. (L3Y2-18110) To prevent damaging the tip, use a wire type plug gap gauge when inspecting the spark plug gap. (L3 ...

Trunk Lid Key Cylinder Removal/Installation
1. Disconnect the negative battery cable.. 2. Remove the trunk lid trim.. 3. Lift the clip in the direction of the arrow (1), and pull out the key rod in the direction of the arrow (2). 4. Remove the nuts. 5. Remove the trunk lid key cylinder. 6. Install in the reverse order of r ...

2016-2022 Copyright www.mazda3tech.com