Mazda 3 Service Manual: Lubrication
- Electric Power Steering Oil Pump Component Disassembly/Assembly
- Electric Power Steering Oil Pump Component Removal/Installation
- Engine Oil Level Inspection [Mzr 2.0, Mzr 2.5]
- Engine Oil Replacement [Mzr 2.0, Mzr 2.5]
- Front Oil Seal Replacement [Mzr 2.0, Mzr 2.5]
- Oil Control Valve (OCV) Inspection [Mzr 2.0, Mzr 2.5]
- Oil Control Valve (OCV) Removal/Installation [Mzr 2.0, Mzr 2.5]
- Oil Cooler Flushing [FS5 A EL]
- Oil Cooler Removal/Installation [FS5 A EL]
- Oil Cooler Removal/Installation [Fw6 A EL]
- Oil Cooler Removal/Installation [Mzr 2.0, Mzr 2.5]
- Oil Filter Replacement [Mzr 2.0, Mzr 2.5]
- Oil Pan Removal/Installation [Mzr 2.0, Mzr 2.5]
- Oil Pressure Inspection [Mzr 2.0, Mzr 2.5]
- Oil Pump Removal/Installation [Mzr 2.0, Mzr 2.5]
- Oil Seal (Control Valve Body) Replacement [Fw6 A EL]
- Oil Seal (Differential) Replacement [A26 M R]
- Oil Seal (Differential) Replacement [C66 M R]
- Oil Seal (Differential) Replacement [Fw6 A EL]
- Oil Seal (Differential) Replacement [G35 M R]
- Oil Seal (Differential) Replacement [G66 M R]
- Oil Seal Replacement [FS5 A EL]
- Rear Oil Seal Replacement [Mzr 2.0, Mzr 2.5]
- Transaxle Oil Inspection [A26 M R]
- Transaxle Oil Inspection [G35 M R]
- Transaxle Oil Inspection [G66 M R]
- Transaxle Oil Replacement [A26 M R]
- Transaxle Oil Replacement [G35 M R]
- Transaxle Oil Replacement [G66 M R]
- Oil Pressure Switch Inspection
- Oil Pressure Switch Inspection [FS5 A EL]
- Oil Pressure Switch Removal
- Oil Pressure Switch Removal/Installation [FS5 A EL]
Mass Air Flow (MAF) Sensor/Intake Air Temperature (Iat) Sensor No.1 Removal/Installation
[Skyactiv G 2.0]
CAUTION:
Be careful not to hit the sensor element or allow foreign matter to get on
it during sensor removal/installation. If the sensor element is hit or foreign
matter gets on it, an e ...
Electric Power Steering Oil Pump Component Disassembly/Assembly
CAUTION:
The internal parts of the EHPAS control module and motor could be damaged
if they receive an impact. Be careful when handling the EHPAS control module
and motor to prevent the c ...
Other materials:
Refrigerant Pressure Sensor Removal/Installation [Manual Air Conditioner]
1. Disconnect the negative battery cable..
2. Discharge the refrigerant..
3. Disconnect the refrigerant pressure sensor connector.
CAUTION:
If moisture or foreign material enters the refrigeration cycle, cooling ability
will be lowered and abnormal noise will occur. Always immediate ...
Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Two Step Deployment
Control System]
WARNING:
A live (undeployed) air bag module or pre-tensioner seat belt may accidentally
operate (deploy) when it is disposed of and cause serious injury. Do not dispose
of a live (undeployed) air bag module and pre-tensioner seat belt. If the SSTs
(Deployment tool and Adapter harnes ...
Drive Plate Removal/Installation [Fw6 A EL]
1. Remove the transaxle..
2. Remove in the order indicated in the table.
1
Drive plate installation bolts
(See Drive Plate Installation Bolts Removal Note.)
(See Drive Plate Installation Bolts Installation Note.)
2
Backing plate
...
