Mazda 3 Service Manual: Emissions
- Canister Vent (Cv) Solenoid Valve Inspection [Mzr 2.0, Mzr 2.5]
- Canister Vent (Cv) Solenoid Valve Removal/Installation [Mzr 2.0, Mzr 2.5]
- Catch Tank Inspection [Skyactiv G 2.0]
- Charcoal Canister Inspection [Mzr 2.0, Mzr 2.5]
- Charcoal Canister Removal/Installation [Mzr 2.0, Mzr 2.5]
- Check Valve (One Way) Inspection [Mzr 2.3 Disi Turbo]
- Check Valve (Two Way) Removal/Installation [Mzr 2.0, Mzr 2.5]
- EGR Pipe Removal/Installation [Mzr 2.3 Disi Turbo]
- EGR Valve Inspection [Mzr 2.0, Mzr 2.5]
- EGR Valve Removal/Installation [Mzr 2.0, Mzr 2.5]
- Positive Crankcase Ventilation (PCV) Valve Inspection [Mzr 2.0, Mzr 2.5]
- Positive Crankcase Ventilation (PCV) Valve Removal/Installation [Mzr 2.0, Mzr
2.5]
- Purge Solenoid Valve Inspection [Mzr 2.0, Mzr 2.5]
- Purge Solenoid Valve Removal/Installation [Mzr 2.0, Mzr 2.5]
- Quick Release Connector (Emission System) Removal/Installation [Mzr 2.0, Mzr
2.5]
- Rollover Valve Inspection [Mzr 2.0, Mzr 2.5]
- Rollover Valve Removal/Installation [Mzr 2.0, Mzr 2.5]
- Warm Up Three Way Catalytic Converter (Wu Twc) Inspection [Mzr 2.0, Mzr 2.5]
- Brake Fluid Pressure Sensor Inspection
- Pressure Sensor Removal/Installation [Two Step Deployment Control System]
- Refrigerant Pressure Sensor Inspection [Full Auto Air Conditioner]
- Refrigerant Pressure Sensor Inspection [Manual Air Conditioner]
- Refrigerant Pressure Sensor Removal/Installation [Full Auto Air Conditioner]
- Refrigerant Pressure Sensor Removal/Installation [Manual Air Conditioner]
WARNING:
Never remove the cooling system cap or loosen the radiator drain plug while
the engine is running, or when the engine and radiator are hot. Scalding engine
coolant and steam may ...
Except for Mexico
Airflow inspection
1. Remove the battery cover..
2. Disconnect the negative battery cable..
3. Remove the CV solenoid valve..
4. Inspect airflow between the ports under the f ...
Other materials:
Master Cylinder Removal/Installation [Mzr 2.3 Disi Turbo]
1. Remove the battery and battery tray..
2. Pinch open the clamps using pliers and disconnect the vacuum hoses from the
insulator bracket as shown in the figure.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
1
Nut ...
Clutch Pedal Removal/Installation [C66 M R]
CAUTION:
Secure the steering wheel using tape or a cable to prevent the steering shaft
from rotating after disconnecting the steering shaft. If the steering wheel
rotates after the steering shaft and the steering gear and linkage are disconnected,
the internal parts of the clock spr ...
Clutch Fluid Inspection [C66 M R]
NOTE:
A common reserve tank is used for the clutch system and brake system.
1. Verify that the clutch fluid is between the MIN mark and the MAX mark.
Verify that there is no clutch fluid leakage then add clutch fluid to the
level between the MIN mark and the MAX mark..
...