Mazda 3 Service Manual: Intake
- Air Cleaner Element Inspection [Mzr 2.0, Mzr 2.5]
- Air Cleaner Element Removal/Installation [Mzr 2.0, Mzr 2.5]
- Air Filter Inspection
- Air Filter Inspection [Mzr 2.0, Mzr 2.5]
- Air Filter Removal/Installation
- Air Filter Removal/Installation [Mzr 2.0, Mzr 2.5]
- Air Intake Actuator Inspection [Full Auto Air Conditioner]
- Air Intake Actuator Inspection [Manual Air Conditioner]
- Air Intake Actuator Removal/Installation [Full Auto Air Conditioner]
- Air Intake Actuator Removal/Installation [Manual Air Conditioner]
- Intake Air System Removal/Installation [Mzr 2.0, Mzr 2.5]
- Intake Air Temperature (Iat) Sensor Inspection [Mzr 2.0, Mzr 2.5]
- Intake Manifold Vacuum Inspection [Mzr 2.0, Mzr 2.5]
- Variable Intake Air Shutter Valve Actuator Inspection [Mzr 2.0, Mzr 2.5]
- Variable Intake Air Solenoid Valve Inspection [Mzr 2.0, Mzr 2.5]
- Manifold Absolute Pressure (Map) Sensor Inspection [Mzr 2.0, Mzr 2.5]
- Manifold Absolute Pressure (Map) Sensor Removal/Installation [Mzr 2.0, Mzr 2.5]
- Manifold Absolute Pressure (Map) Sensor/Boost Air Temperature Sensor Removal/Installation
[Mzr 2.3 Disi Turbo]
- Manifold Absolute Pressure (Map) Sensor/Intake Air Temperature (Iat) Sensor
No.2 Removal/Installation [Skyactiv G 2.0]
- Mass Air Flow (MAF) Sensor Inspection [Mzr 2.0, Mzr 2.5]
- Mass Air Flow (MAF) Sensor/Intake Air Temperature (Iat) Sensor No.1 Removal/Installation
[Skyactiv G 2.0]
WARNING:
Fuel is very flammable liquid. If fuel spills or leaks from the pressurized
fuel system, it will cause serious injury or death and facility breakage. Fuel
can also irritate skin ...
1. Remove the air cleaner element..
2. Inspect the following items:
Has the replacement interval come?
Is the air cleaner element soiled, damaged, or bent?
Are the air cleane ...
Other materials:
Starter Cut Relay Inspection [MTX]
Advanced Keyless Entry And Push Button Start System Only
1. Disconnect the negative battery cable.
2. Remove the following parts:
a. Front scuff plate (LH).
b. Front side trim (LH).
c. Side wall.
d. Console.
3. Set the bonnet release lever out of the way..
4. Remove the lower panel.. ...
Variable Tumble Shutter Valve Switch Inspection [Mzr 2.0, Mzr 2.5]
Voltage Inspection
NOTE:
The variable tumble shutter valve switch cannot be removed as a single unit.
When replacing the variable tumble shutter valve switch, replace it together
with the intake manifold as a single unit.
1. Connect the M-MDS to the DLC–2.
2. Switch the ig ...
Accessory Socket Inspection
Front
1. Disconnect the negative battery cable..
2. Remove the upper panel..
3. Remove the shift lever knob. (MTX).
4. Remove the selector lever knob. (ATX).
5. Remove the shift panel.
6. Remove the accessory socket (front).
7. Connect a tester as shown in the figure and verify that the ...