Mazda 3 Service Manual: Electrical
- Electrical System
- Battery
- Battery Inspection [Mzr 2.0, Mzr 2.5]
- Battery Inspection [Mzr 2.3 Disi Turbo]
- Battery Inspection [Skyactiv G 2.0]
- Battery Recharging [Mzr 2.0, Mzr 2.5]
- Battery Recharging [Mzr 2.3 Disi Turbo]
- Battery Recharging [Skyactiv G 2.0]
- Battery Removal/Installation [Mzr 2.0, Mzr 2.5]
- Battery Removal/Installation [Mzr 2.3 Disi Turbo]
- Battery Removal/Installation [Skyactiv G 2.0]
- Fuses & Junction Blocks
- Front Fog Light Relay Removal/Installation
- Main Fuse Removal/Installation
- Relay Block Inspection [With Advanced Keyless Entry And Push Button Start System]
- Relay Block Removal/Installation [With Advanced Keyless Entry And Push Button Start System]
- Relay Inspection [Mzr 2.0, Mzr 2.5, Mzr 2.3 Disi Turbo]
- Relay Inspection [Skyactiv G 2.0]
- Starter Cut Relay Inspection [MTX]
- Starter Cut Relay Removal/Installation [MTX]
- Ignition
- Forced Ignition On [With Advanced Keyless Entry And Push Button Start System]
- Ignition Coil Inspection [Mzr 2.0, Mzr 2.5]
- Ignition Coil Removal/Installation [Mzr 2.0, Mzr 2.5]
- Ignition Coil Removal/Installation [Mzr 2.3 Disi Turbo]
- Ignition Coil/Ion Sensor Removal/Installation [Skyactiv G 2.0]
- Ignition Key Illumination Removal/Installation
- Spark Plug Inspection [Mzr 2.0, Mzr 2.5]
- Spark Plug Inspection [Mzr 2.3 Disi Turbo]
- Spark Plug Inspection [Skyactiv G 2.0]
- Spark Plug Removal/Installation [Mzr 2.0, Mzr 2.5]
- Spark Plug Removal/Installation [Mzr 2.3 Disi Turbo]
- Spark Plug Removal/Installation [Skyactiv G 2.0]
- Ignition Switch Inspection [Without Advanced Keyless Entry And Push Button Start System]
- Ignition Switch Removal/Installation [Without Advanced Keyless Entry And Push Button Start System]
- Data Network
- Body Control Module (Bcm) Configuration
- Body Control Module (Bcm) Inspection
- Body Control Module (Bcm) Removal/Installation
- Controller Area Network (Can) System
- On Board Diagnostic System PID/Data Monitor Inspection [FS5 A EL]
- On Board Diagnostic System PID/Data Monitor Inspection [Fw6 A EL]
- On Board Diagnostic System Simulation Inspection [FS5 A EL]
- On Board Diagnostic System Simulation Inspection [Fw6 A EL]
- PID/Data Monitor Inspection [Bcm]
- Starting, Charging
- Generator Disassembly/Assembly [Mzr 2.0, Mzr 2.5]
- Generator Inspection [Mzr 2.0, Mzr 2.5]
- Generator Removal/Installation [Mzr 2.0, Mzr 2.5]
- Refrigerant Charging
- Starter Cut Relay Inspection [MTX]
- Starter Cut Relay Removal/Installation [MTX]
- Starter Disassembly/Assembly [Mzr 2.0, Mzr 2.5]
- Starter Inspection [Mzr 2.0, Mzr 2.5]
- Starter Interlock Switch Inspection [Mzr 2.0, Mzr 2.5]
- Starter Interlock Switch Removal/Installation [C66 M R]
- Starter Removal/Installation [Mzr 2.0, Mzr 2.5]
Pilot Bearing Inspection [C66 M R]
1. Without removing the pilot bearing, turn the bearing while applying force
in the axial direction.
If there is any malfunction, replace the pilot bearing..
...
Electrical System
Electrical Parts
Battery cable
Before disconnecting connectors or removing electrical parts, disconnect
the negative battery cable.
Wiring Harness
To remove the wiring ha ...
Other materials:
Restraints SST [Standard Deployment Control System]
49 H066 002
Deployment tool
49 D066 002
Adapter harness
49 L066 002
Adapter harness
49 B066 004
Adapter harness
49 N088 0A0
Fuel and Therm ...
Drive mode select switch
The drive modes of the Subaru Solterra can be adjusted to match different
driving conditions, ensuring optimal performance, efficiency, and comfort.
Selecting a drive mode
By pressing the drive mode select switch, the Subaru Solterra cycles through
three distinct driving modes: Power mode, Nor ...
Canister Vent (Cv) Solenoid Valve Removal/Installation [Mzr 2.0, Mzr 2.5]
Except for Mexico
1. Remove the battery cover..
2. Disconnect the negative battery cable..
3. Remove in the order indicated in the table.
1
CV solenoid valve connector
2
Evaporative hose No.1
3
Evaporative hos ...
