Mazda 3 Service Manual: A/C
- A/C Compressor Removal/Installation
- A/C Unit Disassembly/Assembly
- A/C Unit Removal/Installation
- Air Intake Actuator Inspection [Full Auto Air Conditioner]
- Air Intake Actuator Inspection [Manual Air Conditioner]
- Air Intake Actuator Removal/Installation [Full Auto Air Conditioner]
- Air Intake Actuator Removal/Installation [Manual Air Conditioner]
- Air Mix Actuator Inspection [Full Auto Air Conditioner]
- Air Mix Actuator Removal/Installation [Full Auto Air Conditioner]
- Airflow Mode Actuator Inspection [Full Auto Air Conditioner]
- Airflow Mode Actuator Removal/Installation [Full Auto Air Conditioner]
- Ambient Temperature Sensor Inspection [Full Auto Air Conditioner]
- Ambient Temperature Sensor Inspection [Manual Air Conditioner]
- Ambient Temperature Sensor Removal/Installation [Full Auto Air Conditioner]
- Ambient Temperature Sensor Removal/Installation [Manual Air Conditioner]
- Blower Motor Inspection [Full Auto Air Conditioner]
- Blower Motor Inspection [Manual Air Conditioner]
- Blower Motor Installation [Full Auto Air Conditioner]
- Blower Motor Removal [Full Auto Air Conditioner]
- Blower Motor Removal [Manual Air Conditioner]
- Climate Control Unit Disassembly/Assembly [Manual Air Conditioner]
- Climate Control Unit Inspection [Full Auto Air Conditioner]
- Climate Control Unit Inspection [Manual Air Conditioner]
- Climate Control Unit Removal/Installation [Full Auto Air Conditioner]
- Climate Control Unit Removal/Installation [Manual Air Conditioner]
- Condenser Inspection
- Condenser Removal/Installation
- Drive Belt Inspection [Mzr 2.0, Mzr 2.5]
- Drive Belt Inspection [Mzr 2.3 Disi Turbo]
- Drive Belt Inspection [Skyactiv G 2.0]
- Drive Belt Removal/Installation [Mzr 2.0, Mzr 2.5]
- Drive Belt Removal/Installation [Mzr 2.3 Disi Turbo]
- Drive Belt Removal/Installation [Skyactiv G 2.0]
- Evaporator Inspection
- Expansion Valve Removal/Installation
- Fan Switch Inspection [Manual Air Conditioner]
- Heater, Ventilation And Air Conditioning
- Magnetic Clutch Adjustment [Full Auto Air Conditioner]
- Magnetic Clutch Adjustment [Manual Air Conditioner]
- Magnetic Clutch Disassembly/Assembly [Full Auto Air Conditioner]
- Magnetic Clutch Disassembly/Assembly [Manual Air Conditioner]
- Magnetic Clutch Inspection [Full Auto Air Conditioner]
- Magnetic Clutch Inspection [Manual Air Conditioner]
- Passenger Compartment Temperature Sensor Inspection [Full Auto Air Conditioner]
- Passenger Compartment Temperature Sensor Removal/Installation [Full Auto Air Conditioner]
- Power Metal Oxide Semiconductor Field Effect Transistor (Power Mos Fet) Inspection [Full Auto Air Conditioner]
- Power Metal Oxide Semiconductor Field Effect Transistor (Power Mos Fet) Removal/Installation [Full Auto Air Conditioner]
- Receiver/Drier Removal/Installation
- Evaporator Temperature Sensor Inspection [Full Auto Air Conditioner]
- Evaporator Temperature Sensor Inspection [Manual Air Conditioner]
Rear Heat Duct Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Upper panel.
b. Shift lever knob (MTX).
c. Selector lever knob (ATX).
d. Shift panel.
e. Side wall.
f. Consol ...
A/C Compressor Removal/Installation
1. Disconnect the negative battery cable..
2. Discharge the refrigerant..
3. Remove the aerodynamic under cover No.2..
4. Remove the drive belt..
5. Remove the water hose bracket.
CAUTIO ...
Other materials:
Drive Belt Auto Tensioner Inspection [Skyactiv G 2.0]
WARNING:
A hot engine can cause severe burns. Turn off the engine and wait until it
is cool before servicing.
CAUTION:
If the rubber part of the drive belt auto tensioner is damaged by a screwdriver
or other tool, oil in the hydraulic pressure unit could leak and the tens ...
Front Beltline Molding Removal/Installation
1. Fully open the front door glass.
2. Disconnect the negative battery cable..
3. Remove the inner garnish..
4. Remove the front door trim..
5. Remove the power outer mirror..
6. Remove clip A using a fastener remover and pull the front beltline molding
in the direction of the arrow (1) ...
Power Outer Mirror Switch Inspection
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Inner garnish.
b. Front door trim.
c. Switch panel.
3. Verify that the continuity between the power outer mirror switch terminals
is as indicated in the table.
If not as indicated in the table, replace t ...
