Mazda 3 Service Manual: Doors/Lids & Hood/Trunk
- Door Adjustment
- Door Sash Film Installation
- Door Sash Film Removal
- Front Door Checker Removal/Installation
- Front Door Hinge Removal/Installation
- Front Door Key Cylinder Removal/Installation
- Front Door Key Cylinder Switch Inspection
- Front Door Latch And Lock Actuator Inspection
- Front Door Latch And Lock Actuator Removal/Installation
- Front Door Latch Switch Inspection
- Front Door Module Panel Removal/Installation
- Front Door Removal/Installation
- Front Outer Handle Removal/Installation
- Hood Adjustment
- Hood Disassembly/Assembly
- Hood Latch And Release Lever Removal/Installation
- Hood Latch Switch Inspection
- Hood Release Cable Removal/Installation
- Hood Removal/Installation
- Liftgate Adjustment
- Liftgate Hinge Removal/Installation
- Liftgate Latch And Lock Actuator Inspection
- Liftgate Latch And Lock Actuator Removal/Installation
- Liftgate Latch Switch Inspection
- Liftgate Lock Striker Removal/Installation
- Liftgate Lower Trim Removal/Installation
- Liftgate Opener Switch Inspection
- Liftgate Opener Switch Removal/Installation
- Liftgate Removal/Installation
- Liftgate Side Trim Removal/Installation
- Liftgate Upper Trim Removal/Installation
- Rear Door Checker Removal/Installation
- Rear Door Hinge Removal/Installation
- Rear Door Latch And Lock Actuator Inspection
- Rear Door Latch And Lock Actuator Removal/Installation
- Rear Door Latch Switch Inspection
- Rear Door Module Panel Removal/Installation
- Rear Door Pad Removal/Installation
- Rear Door Removal/Installation
- Rear Outer Handle Removal/Installation
- Stay Damper Disposal
- Trunk Board Removal/Installation
- Trunk Compartment Light Bulb Removal/Installation
- Trunk End Trim Removal/Installation
- Trunk Lid Adjustment
- Trunk Lid Key Cylinder Removal/Installation
- Trunk Lid Latch And Release Actuator Inspection
- Trunk Lid Latch And Release Actuator Removal/Installation
- Trunk Lid Latch Switch Inspection
- Trunk Lid Lock Striker Removal/Installation
- Trunk Lid Opener Cable Removal/Installation
- Trunk Lid Opener Lever Removal/Installation
- Trunk Lid Release Actuator Inspection
- Trunk Lid Removal/Installation
- Trunk Lid Stay Damper Disposal
- Trunk Side Trim Removal/Installation
- Trunk Side Upper Trim Removal/Installation
- Trunk Lid Opener Switch Inspection
- Trunk Lid Opener Switch Removal/Installation
- Front Door Trim Disassembly/Assembly
- Front Door Trim Removal/Installation
- Rear Door Trim Disassembly/Assembly
- Rear Door Trim Removal/Installation
- Trunk Lid Trim Removal/Installation
Body
...
Door Adjustment
1. Loosen the door hinge installation bolts.
2. Adjust the gap and height difference to the standard range by moving the door
back and forth, left and right.
Standard range
a: 2.5 ...
Other materials:
Headlight Aiming
CAUTION:
If the headlight aiming is adjusted with cargo in the vehicle, it may not
adjust correctly. Adjust the headlight aiming with the vehicle under the following
conditions:
No occupants inside vehicle
Cargo other than spare tire, jack, and tools not loaded
...
Antenna Feeder No.1 Inspection
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Center panel.
b. Audio unit.
c. A-pillar trim (RH).
3. Disconnect antenna feeder No.2.
4. Verify that the continuity between antenna feeder No.1 terminals is as indicated
in the table.
If not a ...
Power Systems Personalization Features Setting Procedure
NOTE:
Use the IDS (laptop PC) because the PDS (Pocket PC) does not support the
POWER SYSTEMS PERSONALIZATION FEATURES SETTING PROCEDURE.
1. Connect the M-MDS to the DLC–2.
2. After the vehicle is identified, select the following items from the initial
screen of the M-MDS.
...
